Name: Nice MC800
Brand: Nice
Rating: 5 (1 reviews)

To Next Page

To Previous Page

22 – ENGLISH

TECHNICAL SPECIFICATIONS

11 TECHNICAL SPECIFICATIONS

l

All technical specications stated in this section refer to an ambient temperature of 20°C (± 5°C). Nice S.p.A.

reserves the right to apply modications to the product at any time when deemed necessary, without altering

its functions and intended use.

Table 13

TECHNICAL SPECIFICATIONS

Description Technical specication

MC800 power supply

120/230 V ~ 50/60 Hz

Nominal power absorbed by the mains

grid

900 W

Warning light output

1 warning light (120/230 V, 21 W lamp)

Electric lock output 1 x 12 Va max 15 VA electric lock

Gate open indicator output

1 x 24 V maximum 4 W lamp (the output can also command small relays)

BLUEBUS output

1 output with maximum load of 15 Bluebus units (maximum 6 pairs of MOFB or MOFOB

photocells + 2 pairs of MOFB or MOFOB photocells addressed as opening devices +

maximum 4 MOMB or MOTB control devices

STOP input

for normally closed or normally open contacts or for 8.2 kΩ xed resistor contacts with self-

learning (any variation from the memorised status triggers the “STOP” command)

SbS input

for normally open contacts (closing of the contact triggers the Step-by-Step command)

OPEN input

for normally open contacts (the closing of the contact causes the OPEN command)

CLOSE input

for normally open contacts (the closing of the contact causes the CLOSE command)

Radio connector

SM connector for receivers

Radio ANTENNA input

50 Ω for RG58-type cable or similar

Programmable functions

8 ON-OFF and 8 adjustable functions

Self-learning functions

Self-learning of the devices connected to the BlueBus output; self-learning of the type of

device connected to the “STOP” terminal (NO, NC contact, 8.2 kΩ xed resistor, or 4K1

double edge); self-learning of the gate path and automatic calculation of the slowdown and

partial opening points

Operating temperature

–20°C to +55°C

Use in highly acid, saline or potentially

explosive atmosphere

Protection rating

IP 54 with container intact

Dimensions (mm)

310 x 232 x H 122

Weight (kg)

4,1

CONFORMITY

12 CONFORMITY

EU Declaration of Conformity

and declaration of incorporation of “partly completed machinery”

Note - The contents of this declaration correspond to declarations in the ofcial document deposited at the registered ofces of Nice S.p.a. and in particular to the last revision available before

printing this manual. The text herein has been re-edited for ed

itorial purposes. A copy of the original declaration can be requested from Nice S.p.a. (TV) I.

Number:

637/MC800 Rev: 0 Language: EN

Manufacturer’s Name:

Nice s.p.a.

Address:

Via Callalta 1, Z.I. Rustignè, 31046 Oderzo (TV) Italy

Authorized Person to constitute

technical documentation:

Nice s.p.a.

Type of product:

Control unit with 2 motors 230V

Model/Type:

MC800

Accessories:

Refer to the catalog

The undersigned Roberto Griffa, in the role of Chief Executive Ofcer, declares under his sole responsibility that the product described above complies with the provisions

laid down in the following directives:

•

Directive 2014/30/EU (EMC), according to the following harmonized standards: EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011

The product also complies with the following directives according to the requirements envisaged for “partly completed machiner

y” (Annex II, part 1, section B):

•

Directive 2006/42/EC of the EUROPEAN PARLIAMENT AND COUNCIL of 17 May 2006 related to machinery and amending the Directive 95/16/EC (recast).

It is hereby stated that the relevant technical documentation has been compiled in accordance with annex VII B of Directive 2006/42/EC and that the following essential

requirements have been fullled: 1.1.1 - 1.1.2 - 1.1.3 - 1.2.1 - 1.2.6 - 1.5.1 - 1.5.2 -

1.5.5 - 1.5.6 - 1.5.7- 1.5.8 - 1.5.10 - 1.5.11

The manufacturer undertakes to transmit to the national authorities, in response to a reasoned request, the relevant information on the “ partly completed machinery “, while

maintaining full rights to the related intellectual property.

Should the “ partly completed machinery” be put into service in a European country with an ofcial language other than that used in this declaration, the importer is obliged

to arrange for the relative translation to accompany this declaration.

The “partly completed machinery” must not be used until the nal machine in which it is incorporated is in turn declared as compliant, if applicable, with the provisions of

directive 2006/42/EC.

The product also complies with the following standards:

EN 60335-1:2012+A11:2014, EN 62233:2008, EN 60335-2-103:2015

Oderzo,

16/04/2018

Ing. Roberto Griffa

(Chief Executive Ofcer)