Pandora Elite v2 User Manual

13
12
USER MANUAL PANDORA ELITE V2
SYSTEM FUNCTIONS AND MODES
Security mode
The system confirms arming with 1х
sound and 1х
light signals. When the system is armed, the
system monitors security zones with separated warning and alarm level of triggering:
• Warning mode - this mode activates when there is a slight impact on the shock sensor or additional
senor. It is accompanied with 1х
light and 3х
sound signals;
• Alarm mode - this mode activates when a sensor or one of the security zones is triggered.
It is 30 sec.
light and 30 sec. sound signals. he alarm signals can be
• canceled by an arming or disarming command.
If one of the security zones is triggered the system:
• records this event in its non-volatile memory;
• activates the alarm or warning mode;
• informs an owner by all available means;
• blocks the engine (in accordance with the settings and connections).
• If one of the security zones is opened at the moment of arming, the system will produce 4х
sound and 4х
light warning signals.
If one of the security zones fails, the system will forcibly turn off this zone. If a switch triggers
more than 9 times in a row, it will be disabled until the next arming. The shock/tilt/motion sensor is
temporarily deactivated (15 sec.) if it has been triggered more than 3 times in a row.
The system confirms disarming with 2х
sound and 2х
light signals. The system deactivate
engine blocking (if the immobilizer function and additional blocking are not used). If there were alarm
events during the armed period, the system will produce 4х
sound and 4х
light warning
signals. The system continues to display all zones when it is disarmed, but the information is not saved
in the memory.
Security zones
• Interior temperature (status)
• Engine temperature (status)
• Outside temperature (status)*
• Voltage of the on-board circuits (status)
• Engine operation control - RPM (status)
• Heater operating control (status)
• Fuel level (status)
• Parking (automatic gearbox) /Handbrake (manual gearbox) status
• Parking light is not turned off” notification (status)
• Shock sensor (security zone – alarm and warning level)
• Motion sensor (security zone – alarm level)
• Tilt sensor (security zone – alarm level)
• OE alarm system status via CAN, additional sensor (status, security zone – alarm and warning level)
• Turning ignition on (status, security zone – alarm level)
• Opening doors (status, security zone – alarm level)
• Opening a trunk (status, security zone – alarm level)
• Opening a hood (status, security zone – alarm level)
• Pressing brake (status, security zone – alarm level)
!
*outsIde tempeRAtuRe Is AvAIlAble by AN AddItIoNAl devIce (see the “AddItIoNAl devIces” sectIoN) oR by cAN-bus dAtA
(see loAdeR.pANdoRAINfo.com).
Remote and automatic engine starts
The system allows for remote engine start using the “remote engine start” command from a remote
control, mobile application or preconfigured automatic engine start function. Remote start can be used
to heat engine and interior, charge battery or to cool the interior with air conditioning.
Remote and automatic starts can only be used when the system is armed. While the system is in
remote or automatic start mode, it keeps performing all security functions of all of the security zones
excluding a shock sensor (the system can be configured to not disable the shock sensor during a remote
engine start). To compensate it, the motion sensor sensitivity and responsiveness will be increased. If
any security zone will be triggered, the engine will be immediately stopped and alarm mode will be
triggered.
When using the remote and automatic engine start functions, make sure that a car is secured with
handbrake or some other means of fixating the car on a parking position.
Remote and automatic engine start on automatic transmission cars will only occur, if a transmission
selector lever was left in the «P» position.
If a car has manual transmission, remote or automatic start will only occur if the program neutral
procedure was followed when the car was arming.
AN EXAMPLE OF THE PROGRAM NETURAL PROCEDURE
1. When the engine is running, fixate the car with the handbrake and put gear lever to the neutral
position. Program neutral procedure will be switched on automatically (by default system settings).

Pandora Elite v2 Specifications

General

Brand	Pandora
Model	Elite v2
Category	Car Alarm
Language	English