Pentair intellidrive pid20 User Manual

Safety 2
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual
contains important instructions that should be
followed during installation, operation, and
maintenance of the PENTEK
INTELLIDRIVE Variable
Frequency Drive (VFD).
This is the safety alert symbol. When you see
this symbol on your PENTEK
INTELLIDRIVE or in
this manual, look for one of the following signal
words and be alert to the potential for personal
injury!
indicates a hazard which, if not
avoided, will result in death or serious injury.
indicates a hazard which, if not
avoided, could result in death or serious injury.
indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE addresses practices not related to
personalinjury.
Carefully read and follow all safety instructions in
this manual and on the PENTEK
INTELLIDRIVE.
Keep safety labels in good condition. Replace
missing or damaged safety labels.
California Proposition 65 Warning
This product and related accessories
contain chemicals known to the State of California
to cause cancer, birth defects or other reproductive
harm.
Risk of high-voltage electrical shock
from EMI/RFI filter inside drive. Can shock, burn
or kill if the front cover of the PENTEK
INTELLIDRIVE is open or removed while power is
connected to the Drive or the Drive is running. The
front cover of the Drive must be closed during
operation.
• Makeallwiringconnections,thencloseand
fasten the cover before turning on power to drive.
• NEVER open the box when power is connected to
Drive.
• Beforedoinganyserviceormaintenanceinside
Drive or when connecting or disconnecting any
wires inside Drive:
1. DISCONNECT power.
2. WAIT 5 minutes for retained voltage
todischarge.
3. Open box.
• Beforestartinganywiringorinspection
procedures, check for residual voltage with a
voltage tester.
• NEVER connect power wiring to
Drive before
mounting the box.
• NEVER handle or service
Drive with wet or damp
hands. Always make sure hands are dry before
working on
Drive .
• NEVER reach into or change the cooling fan while
power is applied to Drive.
• NEVER touch the printed circuit board when
power is applied to Drive.
Risk of fire. Can cause severe injury,
property damage or death if installed with incorrect
or inadequate circuit breaker protection. To ensure
protection in the event of an internal fault in the
PENTEK
INTELLIDRIVE, install the Drive on an
independent branch circuit protected by a circuit
breaker (see Table 2 for circuit-breaker sizing), with
no other appliances on the circuit.
Risk of burns. The Drive can become
hot during normal operation. Allow it to cool for
5minutes after shut-down and before handling it to
avoid burns.
NOTICE To avoid damage to Drive or problems
with Drive:
• Connectoutputcablesto3-wire 1-phase and
3-phase submersible motors as follows:
  RedtoR,YellowtoY,BlacktoB.
Any other order will reverse the motor rotation
(3-phase) and may damage the motor.
• Connectoutputcablesto2-wire 1-phase
submersible motors as follows:
Connect to Y and B only.
Connect Ground to green screw.
• Aboveground3-phasemotorsmayhavedifferent
lead colors. Generally connect output leads
asfollows:
  RtoL1,YtoL2,BtoL3.
Verify rotation after startup.
• Donotmodifyequipment.
• Donotusepowerfactorcorrectioncapacitors
as they will damage both motor and
PENTEK
INTELLIDRIVE .
• Donotremoveanypartsunlessinstructedtodo
soinOwner’sManual.
• DonotuseamagneticcontactoronDrivefor
frequent starting/stopping.
• DonotinstalloroperateDriveifitisdamagedor
parts are missing.
• BeforestartingDrivethathasbeeninstorage,
always inspect it and test operation.
• Donotcarryoutamegger(insulationresistance)
test on the control circuit of the
Drive .
• Donotallowlooseforeignobjectswhichcan
conduct electricity (such as screws and metal
fragments) inside Drive box at any time. Do not
allow flammable substances (such as oil) inside
Drive box at any time.
• GroundDriveaccordingtotherequirementsof
the National Electrical Code Section 250, IEC536
Class 1, or the Canadian Electrical Code (as
applicable) , and any other codes and ordinances
that apply.
• Allinstallation,servicework,andinspections
must be done by qualified electrician.

Pentair intellidrive pid20 Specifications

General

Brand	Pentair
Model	intellidrive pid20
Category	Controller
Language	English