Pyronix Enforcer 32WE Setup Guide

29
DELTABELL-WE
External sounder
Printed circuit board
Step 4
Step 5
Tamper
levelling
screw
AC/DC
BATTERY
SOUNDER
TAMPER
LEARN
BAT
+
-
LED3 LED2 LED1
Comfort LED
Enable/Disable
link
Learn button
Optional
auxillary 12
volt PSU input
Battery
Sounder
Tamper
Red LED
Blue LED
Green LED
Strobe
Comfort LEDs
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current.
Replace only with approved batteries.
To prevent possible damage to
components, any static charge on your
body needs to be eliminated before
touching the inside of the unit. This can
be accomplished by touching some
grounded/earthed metallic conductor
such as a radiator/pipework
immediately before replacing batteries.
Battery
Tamper switch
Battery CR3 3.0 volt
11000MAh
Lithium battery
Strobe duration 10mS
Strobe Frequency 1Hz
Sound pressure level 101dBA
Dimensions 290 x 285 x 50 mm
Reverse polarity protected
Tamper
levelling
screw
AC/DC
BATTERY
SOUNDER
TAMPER
LEARN
BAT
+
-
LED3 LED2 LED1
Comfort LED
Enable/Disable
link
Learn button
Optional
auxillary 12
volt PSU input
Battery
Sounder
Tamper
Red LED
Blue LED
Green LED
Strobe
Comfort LEDs
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current.
Replace only with approved batteries.
To prevent possible damage to
components, any static charge on your
body needs to be eliminated before
touching the inside of the unit. This can
be accomplished by touching some
grounded/earthed metallic conductor
such as a radiator/pipework
immediately before replacing batteries.
Battery
Tamper switch
Battery CR3 3.0 volt
11000MAh
Lithium battery
Strobe duration 10mS
Strobe Frequency 1Hz
Sound pressure level 101dBA
Dimensions 290 x 285 x 50 mm
Reverse polarity protected
Tamper
levelling
screw
AC/DC
BATTERY
SOUNDER
TAMPER
LEARN
BAT
+
-
LED3 LED2 LED1
Comfort LED
Enable/Disable
link
Learn button
Optional
auxillary 12
volt PSU input
Battery
Sounder
Tamper
Red LED
Blue LED
Green LED
Strobe
Comfort LEDs
The batteries supplied have been
chosen to provide long service life
whilst, for safety reasons, having
limited output current.
Replace only with approved batteries.
To prevent possible damage to
components, any static charge on your
body needs to be eliminated before
touching the inside of the unit. This can
be accomplished by touching some
grounded/earthed metallic conductor
such as a radiator/pipework
immediately before replacing batteries.
Battery
Tamper switch
Battery CR3 3.0 volt
11000MAh
Lithium battery
Strobe duration 10mS
Strobe Frequency 1Hz
Sound pressure level 101dBA
Dimensions 290 x 285 x 50 mm
Reverse polarity protected
Place the PCB module, ensuring that the arrow is aligned
with the marker (on the left of the module).
Expose the terminals by releasing the latch on the top of the
PCB module.
Fit the lid by sliding its hinges into place. The lid can be supported
in the fully open position; to close the lid, apply a little force to
push the lid past the holds.
Close the cover, ensure the tamper is operating correctly and
insert the 25mm long screw supplied and rotate the screw cover
to a close.

Pyronix Enforcer 32WE Specifications

General

Brand	Pyronix
Model	Enforcer 32WE
Category	Security System
Language	English