Siemens Vector Control User Manual

Control Word and Status Word 05.2006
6SE7087-2JD60 Siemens AG
10-18 Operating Instructions SIMOVERT MASTERDRIVES
1=Synchronism achieved 0=Synchronism not achieved
Function diagram
87654321
Status word 2
MASTERDRIVES VC
- 210 -
Bit 17 Bit 18 Bit 19 Bit 20 Bit 21 Bit 22 Bit 23 Bit 24 Bit 25 Bit 26 Bit 27 Bit 28 Bit 29 Bit 30 Bit 31
1=Flying restart or excitation active 0=Flying restart not active or excitation finished
Meaning
0=Overspeed 1=No overspeed 1=External fault 1 active 0=No external fault 1 1=External fault 2 active 0=No external fault 2 1=External warning active 0=No external warning 1=Converter overload warning active 0=No converter overload warning 1=Converter overtemperature fault active 0=No converter overtemperature fault 1=Converter overtemperature warning active 0=No converter overtemperature warning 1=Motor overtemperature warning active 0=No motor overtemperature warning 1=Motor overtemperature fault active O=No motor overtemperature fault Reserve 1=Motor pulled out/blocked fault active 0=No motor pulled out/blocked fault 1=Bypass contactor energized (only AC units) 0=Bypass contactor not energized 1=Pre-charging active 0=Pre-charging not active 1=Fault during synchronization 0=No fault during synchronization
Status word 2
r553
K0033
Status word 2
Bit No.
Bit 16
•
Display of r553 on the PMU
3031 29 28 27 26 25
24 1617181920212223
from sequence control 1)
from synchronization [X01.6]
from messages [480.7]
from sequence control 1) from sequence control 1) from sequence control 1)
from alarm processing
from block/pullout
diagnosis [485.8]
from fault processing
from alarm processing
from alarm processing
from fault processing
from sequence control 1)
from synchronization [X01.6]
from sequence control 1)
B0132
Fly/Exc active
1
B0133 Fly/Exc n.act.
B0134
Sync reached
1
B0135 Sync n.reached
B0136
Overspeed
1
B0137 No Overspeed
B0138
Ext Fault 1
1
B0139 No Ext Fault 1
B0140
Ext Fault 2
1
B0141 No Ext Fault 2
B0142
Ext Warning
1
B0143 No Ext Warning
B0144
Ovld Warn Drive
1
B0145 No OvldWarn Drv
B0146
Tmp Flt Drive
1
B0147 No Tmp Flt Drv
B0148
TmpWarn Drive
1
B0149 No TmpWarn Drv
B0150
TmpWarnMotor
1
B0151 No TmpWarnMotor
B0152
TmpFltMotor
1
B0153 No TmpFltMotor
B0156
Motor PullOut
1
B0157 No MotorPullOut
B0158
ChrgRelay close
1
B0159 ChrgRelay open
B0160
Sync Fault
1
B0161 No Sync Fault
B0162
Prechrg active
1
B0163 Prechrg n.act.
The sequence control is the internal control (software) for realizing the drive status (r001).
1)
B0255
ExcitationEnd
in addition
2)
2)
n959.28 = 4

Siemens Vector Control Specifications

General

Brand	Siemens
Model	Vector Control
Category	Media Converter
Language	English