Chapter
6:
Using
the
TV~
features
Using
the
PC
settings
feature
You can view an
image
from a PC on the
TV
screen.
When
a
PC
is
connected
to the
TV's
PC IN terminal, you can
use the PC Settings feature to make adjustments to the image.
If
the
edges
of
the picture
are
cut
off, readjust the
Horizontal
Position
and
Vertical
Position.
If
the picture is affected by
interference, readjust the
Clock
Phase
and
Sampling
Clock.
To
adjust
the
PC
settings:
1 Repeatedly press
~
to select
PC
input
mode
(1&
"Selecting
the video input source to view" page 34).
2
Press
M~U
and open the
Setup
menu.
3 Highlight
PC
Settings
and press
8.
Installation
Sleep
Timer
PC
settings
Note:
If a PC is not
connected
or
there is
no
pc
input
signal, this feature will
be
grayed
out
in
the
Setup
menu
4
Press'"
or
... to highlight the item you want to adjust.
5
Press
....
or
~
to make the appropriate adjustments.
Setting
the
PC
Audio
This
function allows you to output
or
mute the sound from
your PC when connecting using the PC IN terminal and an
analog RGB cable.
(1&
page 19)
To
set the
PC
Audio:
1 Press
M~U
and open the
Audio
menu.
2 Highlight
Audio
Setup
and press
8.
3 Press ...
or
... to select
PC
Audio
and then press
....
or
~
to
select
No
or
Yes.
Yes:
When
viewing the PC input, the audio from the
PC
Audio input can be heard.
No:
When viewing the
PC
input, there will be no audio.
Note:
Because the PC
and
HOMI-1 inputs share the
same set
of
analog audio inputs, the
PC
Audio
menu
setting influences the HDMI
1
Audio
menu setting.
If
PC
Audio
is set
to
"No," the HDMI 1
Audio
setting changes
to
"Auto."
If
PC
Audio
is set
to
"Yes," the HDMI 1
Audio
setting
is
set to
"Digital"
and
is
grayed
out
in
the menu.
(Also see item
3 on
page
11
and
"Setting the
HOMITM
Audio
mode"
on
page
32)
Setting
the
sleep
timer
PC
Settings
Note:
The
screen is disrupted momentarily when adjusting
the
PC settings.
This
is
not a sign
of
malfunction.
Horizontal Position
Vertical Position
Clock Phase
Sampling Glock
Auto Adjust
Reset Done
You can set the sleep timer to turn
off
the
TV
after a set
length
of
time
(maximum
of
180 minutes).
To set the sleep
timer
using the remote control:
Press
SOEP
on the remote control to set the length
of
time
until the
TV
turns off. Repeatedly press
SOEP
to increase the
time in 10-minute increments,
or
press'"
or
... to increase or
decrease the time
in
10-minute increments, to a
maximum
of
180 minutes.
Mode
Horizontal
Position
Vertical
Position
Clock
Phase
Sampling
Clock
Auto
Adjust
Description
Moves the picture left/right.
The adjustment range
is
within
±SO
from center.*
Moves the picture up/down.
The adjustment range
is
within ± I0 from center.*
Helps to reduce noise and sharpen the picture.
The adjustment range
is
within ±16 from center.*
Helps to reduce noise and minimize periodic
vertical stripes on the screen.
The
adjustment range
is
within ± I0 from center.*
Highlight this item then press
8 to
get
an
optimum
adjustment
automatically.
To
set the sleep
timer
using the on-screen menus:
1 Press
M~U
and open the
Setup
menu.
2 Highlight
Sleep
Timer
and press
8.
3 Press the
Number
buttons to
enter
the length
of
time in
IO-minute increments.
4 Highlight
Done
and press
8.
Note:
When a
power
failure occurs, the sleep timer
setting
may
be
cleared.
To
display the remaining sleep time:
Press
SOEP.
* The default settings may vary depending
on
the input signal
format.
Note:
A message will display on-screen when there is one
minute remaining on the sleep timer.
To cancel the sleep
timer:
Repeatedly press
SOEP
until it is set to 0 minute.
49
I
To Next Page
Loading...
Need help?
General
