45
0
1
0.0Hz
Upper limit frequency
0.0 6553.5s～
0.0 6553.5s～
By using this function code ,
can be changed without changing any other
parameters . The role of this function code is to adjust
any two lines of the motor (U,V and W) so as to further
change the rotary direction of the motor.
the rotary direction of the
motor
Prompt After parameter initialization , the motor running
direction will restore to the original status . This action
should be carefully performed in the applications where the
rotary direction of the motor is not allowed to change upon
system debugging .
：
Setup range
Lower limit frequency ～
～
650.0 Hz
The inverter starts from the start frequency . If the reference
frequency is lower than frequency lower limit during the
running process ,the inverter will determine the relation
between actual output frequency and lower limit frequency
.in terms of F7.14
Acceleration time refers to the time required for the inverter
to accelerate from 0 Hz to the maximum output frequency .
Deceleration time refers to the time required for the inverter
to decelerate from the maximum output frequency to 0 Hz .
There are still three groups of acceleration / deceleration time
for user selection . Refers to parameter from F7.04
to F7.09 .
descriptions
Group F1 Motor Parameters
When F0.09 is selected as Without memory when power
failure , it means that the setup frequency value is
recovered to the value of F0.08 Digital setup preset
frequency in case of inverter power failure.
WhenF0.09 is selected as With memory when power
failure , it means that the
setup frequency remains the same as before .
“
”
“
”
“
” when the inverter restarts,
Dircetionis consistent
Direction is reverse
Setup range
Setup range
Setup range
Setup range
Output Frequency
Setup
Frequency
Setup Acceleration Time
Actual Acceleration Time
Actual Deceleration Time
Setup Deceleration Time
Fig . 6-1 Schematic diagram for
acceleration / deceleration time
Time
Fmax
0
F0.10
Running direction
F0.11
Upper limit frequency
50.00Hz
F0.12
Lower limit frequency
0.50Hz
F0.13 Acceleration time 1
Model
dependent
Model
dependent
Deceleration time 1
F0.14
Chapter 6 Parameter Description
Factory
default value
Factory
default value
Factory
default value
Factory
default value
Factory
default value
Setup range
0
1
G model:constant torque load
P model:fan and pump load
0
F1.00
Load type
Factory
default value
1460rpm
50.00Hz
220V/380V
)
)
Only user viewing
Only user viewing
0
460V
Upper limit frequency F0.11
common asynchronous motor
～1
(0.1 999.9A～
220V /
0 9999rpm～
(0.4 1000kW～
～
0
～
.0
Motor type selection
1
1
0
Setup range
Setup range
Setup range
Setup range
Setup range
Setup range
Rated power
Rated current
Rated rotation velocity
Rated frequency
Rated voltage
F1.06
F1.05
F1.04
F1.03
F1.01
F1.02
Factory
default value
Factory
default value
Factory
default value
Factory
default value
Factory
default value
Factory
default value
Model
dependent
Model
dependent
To ensure the control performance ,please carry out motor
configurations in accordance with the standard adaptable
motor of the inverter . If there is big difference between
the motor power and the power of standard adaptable motor ,
the control performance of the inverter will decrease
obviously .
F1.07
40%
Setup range
0 100～
In the automatic control mode , the parameter is enabled.
when F2.07=0.0%（）
When the motor is not match the inverter , please setup
the parameter correctly .
Factory
default value
motor no-load
current coefficient
F1.07 =
rated output current of the inverter
motor no-load current
To Next Page
Loading...
General