Yamaha MT-10 2020 User Manual

Instrument and control functions
5-27
1
2
3
4
5
6
7
8
9
10
11
12
3. Turn the accessory off.
4. Insert the accessory plug into the
auxiliary DC jack.
5. Turn the main switch on, and start
the engine. (See page 7-1.)
6. Turn the accessory on.
WARNING
EWA14361
To prevent electrical shock or
short-circuiting, make sure that the
cap is installed when the auxiliary
DC jack is not being used.
EAU15306
Sidestand
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.
TIP
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See the following section for an expla-
nation of the ignition circuit cut-off sys-
tem.)
WARNING
EWA10242
The vehicle must not be ridden with
the sidestand down, or if the sides-
tand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly and have a
Yamaha dealer repair it if it does not
function properly.
1. Auxiliary DC jack
1
B67-9-13.book 27 ページ ２０１９年７月１９日 金曜日 午後２時５６分

Yamaha MT-10 2020 Specifications

General

Bore x Stroke	79.0 mm x 50.9 mm
Compression Ratio	12.0:1
Fuel System	Fuel Injection
Transmission	6-speed
Front Suspension	43mm inverted fork, fully adjustable
Front Brakes	Dual 320mm hydraulic disc, ABS
Rear Brakes	220mm hydraulic disc, ABS
Front Tire	120/70ZR17
Rear Tire	190/55ZR17
Seat Height	825 mm
Starter System	Electric
Final Drive	Chain
Width	800 mm
Engine Type	Liquid-cooled, 4-stroke, DOHC, 4-valve
Fuel Capacity	17 liters
Horsepower	160 HP
Maximum Power	160 HP @ 11500 rpm
Maximum Torque	111 Nm @ 9000 rpm
Length	2, 095 mm
Height	1110 mm
Wheelbase	1, 405 mm
Torque	111 Nm

Summary

Safety information

Safe Riding

Guidelines for safe riding, pre-operation checks, and hazard awareness.

Special features

Traction control system

Function and operation of the traction control system for enhanced grip.

Instrument and control functions

Multi-function meter unit

Details on the speedometer, tachometer, fuel meter, and other displays.

For your safety – pre-operation checks

Fuel

Checks for fuel level, lines, and tank condition before operation.

Coolant

Checking the coolant level in the reservoir and cooling system.

Front brake

Checks for front brake operation, fluid level, pads, and hydraulic system.

Rear brake

Checks for rear brake operation, fluid level, pads, and hydraulic system.

Clutch

Checking clutch operation, cable, and lever free play.

Throttle grip

Ensuring smooth throttle operation and checking free play.

Wheels and tires

Inspection of tires for damage, tread depth, and air pressure.

Sidestand

Operation and important riding points

Starting the engine

Procedures and conditions required for starting the engine.

Shifting

Periodic maintenance and adjustment

General maintenance and lubrication chart

Checking the spark plugs

Engine oil

Checking engine oil level and procedures for oil and filter changes.

Coolant

Air filter element

Tires

Tire inspection, air pressure checks, and replacement guidelines.

Adjusting the clutch lever free play

Checking the brake fluid level

Procedure for checking and replenishing the brake fluid level.

Drive chain slack

Checking the front fork

Battery

Replacing the fuses

Troubleshooting charts

Guides for diagnosing starting problems and poor engine performance.

Engine overheating

Motorcycle care and storage

Consumer information

YAMAHA MOTOR CORPORATION, U.S.A. 2020 AND LATER MODEL STREET & DUAL-PURPOSE MOTORCYCLE LIMITED WARRANTY

THE PERIOD OF WARRANTY