Yamaha MT-10 2020 User Manual

Periodic maintenance and adjustment
8-23
1
2
3
4
5
6
7
8
9
10
11
12
 Insufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.
 Clean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
 Use only the specified brake flu-
id; otherwise, the rubber seals
may deteriorate, causing leak-
age.
 Refill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
 Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.
EAU22734
Changing the brake fluid
Have a Yamaha dealer change the
brake fluid every 2 years. In addition,
have the seals of the master cylinders
and brake calipers, as well as the brake
hoses replaced at the intervals listed
below or sooner if they are damaged or
leaking.
 Brake seals: every 2 years
 Brake hoses: every 4 years
EAU22762
Drive chain slack
The drive chain slack should be
checked before each ride and adjusted
if necessary.
EAU74253
To check the drive chain slack
1. Place the motorcycle on the sides-
tand.
TIP
When checking and adjusting the drive
chain slack, there should be no weight
on the motorcycle.
2. Shift the transmission into the neu-
tral position.
3. Measure the drive chain slack as
shown.
B67-9-13.book 23 ページ ２０１９年７月１９日 金曜日 午後２時５６分

Yamaha MT-10 2020 Specifications

General

Bore x Stroke	79.0 mm x 50.9 mm
Compression Ratio	12.0:1
Fuel System	Fuel Injection
Transmission	6-speed
Front Suspension	43mm inverted fork, fully adjustable
Front Brakes	Dual 320mm hydraulic disc, ABS
Rear Brakes	220mm hydraulic disc, ABS
Front Tire	120/70ZR17
Rear Tire	190/55ZR17
Seat Height	825 mm
Starter System	Electric
Final Drive	Chain
Width	800 mm
Engine Type	Liquid-cooled, 4-stroke, DOHC, 4-valve
Fuel Capacity	17 liters
Horsepower	160 HP
Maximum Power	160 HP @ 11500 rpm
Maximum Torque	111 Nm @ 9000 rpm
Length	2, 095 mm
Height	1110 mm
Wheelbase	1, 405 mm
Torque	111 Nm

Summary

Safety information

Safe Riding

Guidelines for safe riding, pre-operation checks, and hazard awareness.

Special features

Traction control system

Function and operation of the traction control system for enhanced grip.

Instrument and control functions

Multi-function meter unit

Details on the speedometer, tachometer, fuel meter, and other displays.

For your safety – pre-operation checks

Fuel

Checks for fuel level, lines, and tank condition before operation.

Coolant

Checking the coolant level in the reservoir and cooling system.

Front brake

Checks for front brake operation, fluid level, pads, and hydraulic system.

Rear brake

Checks for rear brake operation, fluid level, pads, and hydraulic system.

Clutch

Checking clutch operation, cable, and lever free play.

Throttle grip

Ensuring smooth throttle operation and checking free play.

Wheels and tires

Inspection of tires for damage, tread depth, and air pressure.

Sidestand

Operation and important riding points

Starting the engine

Procedures and conditions required for starting the engine.

Shifting

Periodic maintenance and adjustment

General maintenance and lubrication chart

Checking the spark plugs

Engine oil

Checking engine oil level and procedures for oil and filter changes.

Coolant

Air filter element

Tires

Tire inspection, air pressure checks, and replacement guidelines.

Adjusting the clutch lever free play

Checking the brake fluid level

Procedure for checking and replenishing the brake fluid level.

Drive chain slack

Checking the front fork

Battery

Replacing the fuses

Troubleshooting charts

Guides for diagnosing starting problems and poor engine performance.

Engine overheating

Motorcycle care and storage

Consumer information

YAMAHA MOTOR CORPORATION, U.S.A. 2020 AND LATER MODEL STREET & DUAL-PURPOSE MOTORCYCLE LIMITED WARRANTY

THE PERIOD OF WARRANTY