EasyManuals Logo
Home>Cisco>Network Router>XR 12000 Series

Cisco XR 12000 Series Hardware Installation Guide

Cisco XR 12000 Series
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #80 background imageLoading...
Page #80 background image
2-50
Cisco XR 12000 Series Router SIP and SPA Hardware Installation Guide
OL-17438-04
Chapter 2 Overview: Cisco XR 12000 Series Router Shared Port Adapters
8-Port OC-3 STM-1/OC-12 STM-4 POS SPA Overview
Table 2-35 describes the 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA LEDs.
8-Port OC-3 STM-1/OC-12 STM-4 POS SPA Interface Specifications
The framer processes incoming and outgoing SONET or SDH frames. The framer operates at OC-3 line
rates (155.52 Mbps) and OC-12 line rates (622.08 Mbps). Packet data is transported with a
user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the Layer 2
frame.
The 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA interface complies with the following RFCs:
RFC 1662, PPP in HDLC-like Framing
RFC 2427, Multiprotocol Interconnect over Frame Relay
RFC 2615, PPP over SONET/SDH
8-Port OC-3 STM-1/OC-12 STM-4 POS SPA Optical Transceiver Modules and
Cables
The 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA uses a small form-factor pluggable (SFP) optical
transceiver module installed in each port for SONET and SDH single-mode and multimode optical fiber
connections (see Figure 2-35).
Cisco Systems qualifies the optics that are approved for use with its SPAs. The following OC-3 optical
transceiver modules are supported on the 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA:
Multimode (MM) SFP module—SFP-OC3-MM
Short-reach (SR) SFP module—SFP-OC3-SR
Intermediate-reach (IR) SFP module (15 km)—SFP-OC3-IR1
Long-reach (LR) SFP module (40 km)—SFP-OC3-LR1
Long-reach (LR) SFP module (80 km)—SFP-OC3-LR2
Table 2-35 8-Port OC-3 STM-1/OC-12 STM-4 POS SPA LEDs
LED Label Color State Meaning
C/A Off Off SONET controller is shut down.
Green On Port is enabled by software, and there is a valid SONET signal
without any alarms.
Amber On Port is enabled by software, and there is at least one alarm.
A/L Off Off Interface is shut down.
Green On Port is enabled by software, and loopback is off.
Amber On Port is enabled by software, and loopback is on.
STATUS Off Off SPA power is off.
Green On SPA is ready and operational.
Amber On SPA power is on and good, and the SPA is being configured.

Table of Contents

Other manuals for Cisco XR 12000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco XR 12000 Series and is the answer not in the manual?

Cisco XR 12000 Series Specifications

General IconGeneral
BrandCisco
ModelXR 12000 Series
CategoryNetwork Router
LanguageEnglish

Related product manuals