Danfoss VLTAutomationDrive FC 360 User Manual

7-2* Process Ctrl. Feedb 7-20 Process CL Feedback 1 Resource
*[0] >No function<
[1] >Analog Input 53< [2] >Analog Input 54<
[3] >Frequency input 29<
[4] >Frequency input 33<
7-22 Process CL Feedback 2 Resource
7-3* Process PID Ctrl. 7-30 Process PID Normal/ Inverse Control
*[0] >Normal< [1] >Inverse< 7-31 Process PID Anti Windup
[0] >Off< *[1] >On< 7-32 Process PID Start Speed
>0 - 6000 rpm< *0 rpm
7-33 Process PID Proportional Gain
>0.00 - 10.00< *0.01
7-34 Process PID Integral Time
>0.10-9999.00 s< *9999.00 s
7-35 Process PID Differentiation Time
>0.00-20.00 s< *0.00 s
7-36 Process PID Diff. Gain Limit 7-38 Process PID Feed Forward Factor
>0-200%< *0%
7-39 On Reference Bandwidth
7-4* Adv. Process PID I
7-40 Process PID I-part Reset 7-41 Process PID Output Neg. Clamp
7-42 Process PID Output Pos. Clamp
7-43 Process PID Gain Scale at Min. Ref.
7-44 Process PID Gain Scale at Max. Ref.
7-45 Process PID Feed Fwd Resource
*[0] >No function< [1] >Analog Input 53< [2] >Analog Input 54< [7] >Frequency input 29<
[8] >Frequency input 33<
[11] >Local bus reference< [32] >Bus PCD<
7-46 Process PID Feed Fwd Normal/ Inv.
Ctrl.
7-48 PCD Feed Forward 7-49 Process PID Output Normal/ Inv. Ctrl.
7-5* Adv. Process PID II
7-50 Process PID Extended PID
7-51 Process PID Feed Fwd Gain
7-52 Process PID Feed Fwd Ramp up
7-53 Process PID Feed Fwd Ramp down
7-56 Process PID Ref. Filter Time
7-57 Process PID Fb. Filter Time
7-6* Feedback Conversion 7-60 Feedback 1 Conversion *[0] >Linear< [1] >Square root< 7-62 Feedback 2 Conversion 8-** Comm. and Options 8-0* General Settings
8-01 Control Site 8-02 Control Source 8-03 Control Timeout Time 8-04 Control Timeout Function 8-1* Ctrl. Word Settings 8-10 Control Word Profile 8-3* FC Port Settings 8-30 Protocol *[0] >FC< [2] >Modbus RTU< 8-31 Address 8-32 Baud Rate [0] >2400 Baud< [1] >4800 Baud<
*[2] >9600 Baud< [3] >19200 Baud<
[4] >38400 Baud< [5] >57600 Baud< [6] >76800 Baud<
[7] >115200 Baud< 8-33 Parity / Stop Bits *[0] >Even Parity, 1 Stop Bit<
[1] >Odd Parity, 1 Stop Bit<
[2] >No Parity, 1 Stop Bit<
[3] >No Parity, 2 Stop Bits<
8-35 Minimum Response Delay 8-36 Maximum Response Delay 8-37 Maximum Inter-char delay
8-4* FC MC protocol set 8-43 PCD Read Configuration 8-5* Digital/Bus 8-50 Coasting Select 8-51 Quick Stop Select 8-52 DC Brake Select 8-53 Start Select
8-54 Reversing Select 8-55 Set-up Select 8-56 Preset Reference Select
8-57 Profidrive OFF2 Select 8-58 Profidrive OFF3 Select
8-8* FC Port Diagnostics 8-80 Bus Message Count 8-81 Bus Error Count 8-82 Slave Messages Rcvd
8-83 Slave Error Count
8-84 Slave Messages Sent
8-85 Slave Timeout Errors
8-88 Reset FC port Diagnostics
13-** Smart Logic 13-0* SLC Settings 13-00 SL Controller Mode *[0] >Off< [1] >On< 13-01 Start Event [0] >False< [1] >True< [2] >Running<
[3] >In range< [4] >On reference<
[7] >Out of current range<
[8] >Below I low< [9] >Above I high< [16] >Thermal warning< [17] >Mains out of range<
[18] >Reversing< [19] >Warning< [20] >Alarm (trip)< [21] >Alarm (trip lock)<
[22] >Comparator 0< [23] >Comparator 1<
[24] >Comparator 2< [25] >Comparator 3<
[26] >Logic rule 0<
[27] >Logic rule 1< [28] >Logic rule 2<
[29] >Logic rule 3< [33] >Digital input DI18<
[34] >Digital input DI19< [35] >Digital input DI27< [36] >Digital input DI29< *[39] >Start command< [40] >Drive stopped<
[42] >Auto Reset Trip<
[50] >Comparator 4<
[51] >Comparator 5<
[60] >Logic rule 4< [61] >Logic rule 5<
[83] >Broken Belt< 13-02 Stop Event
*[0] >Off< [1] >On< 13-01 Start Event [0] >False< [1] >True< [2] >Running< [3] >In range<
[4] >On reference< [7] >Out of current range<
[8] >Below I low< [9] >Above I high< [16] >Thermal warning< [17] >Mains out of range<
[18] >Reversing< [19] >Warning< [20] >Alarm (trip)< [21] >Alarm (trip lock)<
[22] >Comparator 0< [23] >Comparator 1<
[24] >Comparator 2<
[25] >Comparator 3<
[26] >Logic rule 0<
[27] >Logic rule 1< [28] >Logic rule 2<
[29] >Logic rule 3< [30] >SL Time-out 0<
[31] >SL Time-out 1<
[32] >SL Time-out 2<
[33] >Digital input DI18<
[34] >Digital input DI19< [35] >Digital input DI27< [36] >Digital input DI29< [39] >Start command< *[40] >Drive stopped< [42] >Auto Reset Trip<
[50] >Comparator 4< [51] >Comparator 5<
[60] >Logic rule 4<
[61] >Logic rule 5< [70] >SL Time-out 3<
[71] >SL Time-out 4<
[72] >SL Time-out 5<
[73] >SL Time-out 6< [74] >SL Time-out 7<
[83] >Broken Belt< 13-03 Reset SLC
*[0] >Do not reset SLC< [1] >Reset SLC<
13-1* Comparators 13-10 Comparator Operand 13-11 Comparator Operator
13-12 Comparator Value
13-2* Timers 13-20 SL Controller Timer 13-4* Logic Rules 13-40 Logic Rule Boolean 1
13-41 Logic Rule Operator 1
13-42 Logic Rule Boolean 2
13-43 Logic Rule Operator 2
13-44 Logic Rule Boolean 3
13-5* States 13-51 SL Controller Event 13-52 SL Controller Action 14-** Special Functions 14-0* Inverter Switching 14-01 Switching Frequency [0] >Ran3< [1] >Ran5< [2] >2.0 kHz< [3] >3.0 kHz< [4] >4.0 kHz< *[5] >5.0 kHz< [6] >6.0 kHz< [7] >8.0 kHz< [8] >10.0 kHz<
[9] >12.0kHz< [10] >16.0kHz< 14-03 Overmodulation
[0] >Off< *[1] >On< 14-08 Damping Gain Factor
14-1* Mains On/Off 14-10 Mains Failure *[0] >No function< [1] >Ctrl. ramp-down<
>[2]< >Ctrl. ramp-down, trip<
[3] >Coasting< [4] >Kinetic back-up<
[5] >Kinetic back-up, trip<
[6] >Alarm<
14-11 Mains Voltage at Mains Fault
14-12 Function at Mains Imbalance
*[0] >Trip< [1] >Warning< [2] >Disabled< [3] >Derate< 14-15 Kin. Backup Trip Recovery Level
14-2* Reset Functions 14-20 Reset Mode
*[0] >Manual reset< [1] >Automatic reset x 1<
[2] >Automatic reset x 2<
[3] >Automatic reset x 3<
[4] >Automatic reset x 4<
[5] >Automatic reset x 5<
[6] >Automatic reset x 6<
[7] >Automatic reset x 7< [8] >Automatic reset x 8<
[9] >Automatic reset x 9<
[10] >Automatic reset x 10<
[11] >Automatic reset x 15<
[12] >Automatic reset x 20<
14-21 Automatic Restart Time
>0-600 s< *10 s
14-22 Operation Mode
*[0] >Normal operation< [2] >Initialisation< 14-23 Typecode Setting
14-24 Trip Delay at Current Limit
14-25 Trip Delay at Torque Limit
14-27 Action At Inverter Fault [0] >Trip< *[1] >Warning or trip after warning<
14-28 Production Settings 14-29 Service Code
14-3* Current Limit Ctrl. 14-30 Current Lim Ctrl, Proportional Gain
14-31 Current Lim Ctrl, Integration Time
14-32 Current Lim Ctrl, Filter Time
14-4* Energy Optimising 14-40 VT Level 14-41 AEO Minimum Magnetisation
>40-75%< *66%
14-5* Environment 14-50 RFI Filter 14-51 DC-Link Voltage Compensation 14-52 Fan Control *[5] >Constant-on mode< [6] >Constant-off mode<
[7] >On-when-Inverter-is-on-else-off
Mode<
[8] >Variable-speed mode<
14-55 Output Filter
14-6* Auto Derate 14-63 Min Switch Frequency *[2] >2.0 kHz< [3] >3.0 kHz<
User Interface and Programm...
VLT
®
AutomationDrive FC 360 Quick Guide
26 MG06A102 - VLT
®
is a registered Danfoss trademark
44

Danfoss VLTAutomationDrive FC 360 Specifications

General

Brand	Danfoss
Model	VLTAutomationDrive FC 360
Category	Controller
Language	English