Dell PowerEdge R310 User Manual

Installing System Components 111
10 Replace the cooling shroud . See "Installing the Cooling Shroud" on
page 102.
11 Close the system. See "Closing the System" on page 79.
12 Start up the system, press <F2> to enter the System Setup program, and
check the
System Memory setting on the main System Setup screen.
The system should have already changed the value to reflect the newly
installed memory.
13 If the value is incorrect, one or more of the memory modules may not be
installed properly. Repeat step 2 through step 12 of this procedure, checking to
ensure that the memory modules are firmly seated in their sockets.
14 Run the system memory test in the system diagnostics. See "Running the
Embedded System Diagnostics" on page 162.
Removing Memory Modules
WARNING: The memory modules are hot to touch for some time after the system has
been powered down. Allow time for the memory modules to cool before handling
them. Handle the memory modules by the card edges and avoid touching the
components on the memory module.
CAUTION: Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your product
documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Read and follow the safety instructions that came with the product.
1 Turn off the system, including any attached peripherals, and disconnect the
system from the electrical outlet.
2 Open the system. See "Opening the System" on page 78.
3 Remove the cooling shroud . See "Removing the Cooling Shroud" on
page 101.
4 Locate the memory module sockets. See Figure 6-1 .
5 Press down and out on the ejectors on each end of the socket until the memory
module pops out of the socket. See Figure 3-15.
Handle each memory module only on either card edge, making sure not to
touch the middle of the memory module.
6 Replace the cooling shroud . See "Installing the Cooling Shroud" on page 102.
R310HOM.book Page 111 Thursday, March 4, 2010 1:03 AM

Dell PowerEdge R310 Specifications

General

Tcase	72.7 °C
Bus type	DMI
Stepping	B1
FSB Parity	No
Processor code	SLBJH
Processor cache	8 MB
Processor cores	4
Processor model	X3470
System bus rate	2.5 GT/s
Processor series	Intel Xeon 3400 Series
Processor socket	LGA 1156 (Socket H)
Processor threads	8
Processor codename	Lynnfield
Motherboard chipset	Intel® 3420
Processing Die size	296 mm²
Processor frequency	2.93 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor manufacturer	Intel
Processor package size	37.5 x 37.5 mm
Processor front side bus	- MHz
Processor boost frequency	3.6 GHz
Processor operating modes	64-bit
ECC supported by processor	Yes
PCI Express configurations	1x16, 2x8, 4x4
Supported instruction sets	SSE4.2
Thermal Design Power (TDP)	95 W
Number of processors installed	1
CPU multiplier (bus/core ratio)	22
Maximum number of PCI Express lanes	16
Memory types supported by processor	DDR3-SDRAM
Number of Processing Die Transistors	774 M
Memory channels supported by processor	Dual
Memory clock speeds supported by processor	800, 1066, 1333 MHz
Memory bandwidth supported by processor (max)	21 GB/s
Maximum internal memory supported by processor	32 GB
HDD size	3.5 \
Optical drive type	DVD-RW
Total storage capacity	500 GB
Maximum storage capacity	8 TB
Number of HDDs installed	-
Memory slots	6x DIMM
Internal memory	2 GB
Graphics card	G200eW
LAN controller	Broadcom BCM5716
Networking features	Gigabit Ethernet
PS/2 ports quantity	0
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
PCI Express slots version	2.0
Power supply	350 W
Compatible operating systems	Windows Server Novell Linux Solaris10
Chassis type	Rack (1U)
Processor ARK ID	42932
Intel® Turbo Boost Technology	1.0

Weight and Dimensions

Depth	610 mm
Width	434 mm
Height	42.4 mm