FO3 - With Disarm: this option will trigger AUX 2 (output time based on feature 4-02) any time the
CM7 is unlocked/disarmed. Note: the system has to be in the armed state when disarming in order
to trigger AUX 1. (I.e. if the vehicle is already in the unlocked/disarmed state and you send a second
unlock/disarm command it will not trigger the output)
FO4 - With Start: This option will trigger the AUX 2 (output time based on feature 4-02) when the
remote start sequence is initiated. It will trigger at the same time as GWR (ground when running)
4-05 Secure Aux Output: this feature is designed to prevent accidental activation of the AUX outputs by
requiring an additional step when using any 4 button or 2 way LCD Firstech remote.
FO1- On: (default) this option will require the user to perform an additional step before activating
AUX output using any Firstech 4 button or 2 way LCD remote (2way remotes with Roman numeral
buttons will require a 0.5 second tap of button IV before activating any of the AUX outputs.2Way LCD
remotes with lock/unlock/trunk/start icons on the buttons use the start button for the same. 1way
remotes require the user to hold trunk + start buttons for 2.5 seconds before activating AUX outputs.)
FO2- Off: this option will disable the additional step required by the user to activate the AUX outputs.
*NEW* FO3- On while armed: this feature will only require the user to perform the additional
override step to activate Aux outputs ONLY WHEN the CM7 is ARMED. While the system is
disarmed or unlocked this step is not required.
4-08 Sliding door control for datalink: (must be enabled to allow data to data sliding door control)
This feature will provide an Unlock or Factory Alarm Disarm (FAD) output when triggering the AUX
control using iDatalink Modules (Sliding Doors)
FO1 - Off: (default) This option does not provide an unlock or a FAD output when activating AUX
output control using the iDatalink modules.
FO2 - Unlock and FAD: This option will provide unlock and a FAD output when activating AUX
output control using iDatalink modules.
FO3 - FAD only: This option will only provide a FAD (factory alarm disarm) output when activating
AUX output control using iDatalink modules.
4-09 PIC 3 (-): (Programmable Input Channel 3 CN5 Pin 1 brown/white) this feature will determine the
input function of PIC 3.
FO1 - Keysense: (default) INPUT only this option will allow PIC to read negative input as a
Keysense input. This is recommended for manual transmission vehicles, EZGO systems, and when
using passive arming. This prevents any action by the CM7 until (-) negative is removed from the
input.
FO2 - Glow plug: This option will allow PIC to read any negative input as a glow plug or wait to
start input. This is recommended for diesel vehicles that may have a negative analog glow plug output
available.
FO3 - Disable Arm/Disarm/Trigger Start: This feature can be used to disable an analog
arm, disarm, and start input to the CM7 when it sees a (-) negative input at the same time. (I.e. can
be connected to a passenger door lock motor wire to prevent disarming the CM7. When the vehicle
door lock switch is used to unlock all doors, this will see an input at the same time as the CM7 disarm
input trigger from the driver’s door lock motor wire. This will prevent it from being disarmed unless the
factory keyless is used.)
Copyright 2014 Firstech, LLC. Page 3Copyright 2014 Firstech, LLC. Page 3Copyright 2014 Firstech, LLC. Page 43
CM7200 Master Guide
Starter System
techfeed.compustar.com
To Next Page
Loading...
Need help?
General
