Fusion Apollo MS-RA670 User Manual

Select > SETTINGS > NETWORK > GARMIN MARINE
NETWORK.
Setting a Static IP Address
If the stereo is configured as a static IP, it is automatically
assigned the IP address of 192.168.0.1. You can change this IP
address.
If the stereo is a DHCP client on the network and you do not
want the DHCP server to automatically assign an IP address to
the stereo, you can set a static IP address.
NOTE: Every device on the network must have a unique IP
address. If you select a static IP address that is the same as the
IP address on the network, the devices will not work properly.
1
Select > SETTINGS > NETWORK > STATIC IP.
2
Select an option:
• To set the IP address, select IP, and enter the IP address.
• To set the subnet mask, select MASK, and enter the
subnet mask.
NOTE: The subnet mask must match all other devices on
the network to work properly. A typical subnet mask is
255.255.255.0.
• To set the default gateway IP address, select GATEWAY,
and enter the gateway IP address.
NOTE: The default gateway is typically set as the IP
address of the DHCP server on the network.
3
Select SAVE.
Resetting Network Settings
You can reset all network settings for this stereo to the factory
default values.
Select > SETTINGS > NETWORK > RESET > YES.
Update Options
Select > SETTINGS > UPDATE.
NOTICE
Do not turn off the device or disconnect the power during a
software update. Turning off the power during a software update
may cause the device to become unresponsive.
NOTE:
• You should update the device software using a USB flash
drive.
• If the stereo is connected to a wireless network, you can
update the software using the Fusion-Link app on a mobile
device.
• The device may restart a few times when updating. This is
normal.
• You can program only newer versions of software on the
device.
STEREO: Updates the stereo.
NRX REMOTE: Updates an optional NRX remote connected to
the NMEA 2000 port or NMEA 2000 network using a valid
software update file on a connected USB flash drive.
ERX REMOTE: Updates an optional remote connected to the
ETHERNET port or the Fusion PartyBus network using a
valid software update file on a connected USB flash drive.
DAB MODULE: Updates an optional DAB module connected to
the SIRIUS XM port using a valid software update file on a
connected USB flash drive.
FACTORY RESET: Restores all settings to the factory default
values.
REFRESH NETWORK: Clears discovered stereos from the
device and searches for new stereos on the network.
Additional Stereo Control Options
Connecting to a Garmin Watch
For a list of a compatible Garmin watches, go to
www.fusionentertainment.com.
For more information about the watch, see the watch manual at
www.garmin.com/manuals.
1
Following the instructions in the watch manual, install the
Fusion-Link Lite
™
app from the Connect IQ
™
store onto the
watch.
2
On the stereo, select the BT source.
3
Select > DISCOVERABLE.
The stereo remains discoverable for two minutes.
4
Bring the watch within 3 m (10 ft.) of the stereo.
NOTE: Stay 10 m (33 ft.) away from other ANT
®
devices
while pairing.
5
Open the Fusion-Link Lite app on the watch.
The first time you open the app on the watch, the watch
automatically pairs with and connects to the stereo. If you
need to pair to another stereo, in the Fusion-Link Lite app,
select Settings > Pair new.
6
Control the audio playback using the Fusion-Link Lite app on
the watch.
After the devices are paired, they connect automatically when
they are turned on, within range, and the app is open on the
watch.
Connecting to an ARX70 Remote Control
1
On the stereo, select the BT source.
2
Select > DISCOVERABLE.
3
Bring the ARX70 remote control within 10 m (33 ft.) of the
stereo.
NOTE: Stay 10 m (33 ft.) away from other ANT devices while
pairing.
4
On the ARX70 remote control, press and hold until the
status LED starts alternating green and red.
The remote control searches for the stereo. When the remote
control pairs successfully, the status LED turns on green
briefly and then turns off.
If the remote control cannot find the stereo, the status LED turns
on red briefly and then turns off.
Fusion-Link Wireless Remote Control App
You can use the Fusion-Link remote control app on your
compatible Apple or Android device to adjust the stereo volume,
change the source, control playback, select and manage radio
presets, and adjust some stereo settings.You can use the app to
set up and configure DSP profiles on the stereo.
The app communicates with the stereo using a wireless
connection to the mobile device. You must connect your
compatible device to the stereo using Bluetooth technology to
use the app.
If the stereo is connected to a network with a Wi‑Fi access point,
the app can communicate with the stereo using the network for
greater range than a Bluetooth connection.
You can connect an Apple device to the stereo using a USB
cable to update the stereo software.
For information about the Fusion-Link remote control app for
compatible Apple or Android devices, go to the Apple App
Store
SM
or the Google Play
™
store.
12 Additional Stereo Control Options

Fusion Apollo MS-RA670 Specifications

General

Brand	Fusion
Model	Apollo MS-RA670
Category	Marine Equipment
Language	English