Grundig 49 GFB 6622 User Manual

93
ENGLISH
SETTING FURTHER CHANNELS
-----------------------------------------------------
Antenna settings, SCR system
and searching for digital chan-
nels from a satellite automati-
cally
Notes:
7
Your TV supports SCR system (Single Chan-
nel Router – EN 50494).
7
The following description about the LNB set-
tings premise a substantial expertise about
the satellite systems. Ask your specialist
dealer.
1 Open the menu with »MENU«.
2 Select menu item »Settings« with »
V «, » Λ «,
»
<
« or »
>
« and press »OK« to confirm.
3 Select the menu item »Source« with »
>
« or
»
<
« and press » V « to confirm.
– »Source« menu is active.
4 Select the line »Automatic Channel Search«
with »
V « or » Λ « and press »OK« to
confirm.
5 Select the option »Satellite (DVB-S/S2)«
with »
V « or » Λ « and press »OK« to
confirm.
6 Select the line »Antenna Settings« with »
V «
or »
Λ « and press »OK« to confirm.
– The »Antenna Settings« menu is dis-
played.
7 Select and set the required option for the
antenna settings with »
V « or » Λ «:
Satellite
Press »OK« then select the required satel-
lite with »
V « or » Λ « and press »OK« to
confirm.
LNB type
If your antenna system is equipped with a
single-cable system multiswitch, use the op-
tion »Grundig SCR«. Press »OK« and select
the »Grundig SCR« option with »
<
« or »
>
«.
Select the »LNB-Frequency High« line with
»
V « and enter the frequency with »1...0«
in five digits.
Select the »LNB-Frequency Low« line with
»
V « and enter the frequency with »1...0«
in five digits.
Confirm the settings with »

« (green).
LNB selection
Depending on the number of LNBs, select
the option with »
<
« or »
>
«.
»1/2« if only 1 LNB is used; if two LNBs
are used, select the required LNB
(»1/2« or »2/2«).
User band
Select the number of the antenna socket
used with »
<
« or »
>
«.
UB frequency (MHz)
Enter the required frequency for the selected
antenna socket with »1...0«.
Notes:
7
Use installation equipment supported / sug-
gested by your SCR Switch.
7
Other users / receivers connected to the
system may be affected if the specified user
band number and frequency is changed
during installation.
7
User band and user band frequency is
specified on the SCR switch used; and each
user / receiver must select a specified user
band and user band frequency.
7
With SCR satellite system, auto search by
several users / receivers at the same time
may cause problems.
8 Exit the antenna settings with »

« (blue).
9 Select the Channel Type.
Press »
V « or » Λ « to select whether you
want to search for only digital channels
(Digital) or only radio channels (Radio) or
both (Digital + Radio) and press »OK« to
select and mark or unmark the »Digital«
and/or »Radio« items.
10 Select Scan Mode.
To select whether you want to search for
only free digital television channels (Free),
only scrambled digital television channels
(Scrambled) or both (Free + Scrambled),
press »
V « or » Λ « and press OK« to select
and mark or unmark the »Free« and/or
»Scrambled« items.

Grundig 49 GFB 6622 Specifications

General

Brand	Grundig
Model	49 GFB 6622
Category	TV
Language	English