Intex ECO20110-2 User Manual

FILTER DOESN 'T
CLEAN POOL
FILTER DOESN 'T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMP DOESN'T
WORK
6-WAY VALVE/
COVER LEAKING
H OSE LEAKING
TIMER IS
INACCURA
TE OR
TIMER CA N'T BE SET
PRESSURE GAUGE
DOESN'T WORK
I NLET THREADED
A IR C ONNECTOR
/A IR JET VALVE
LEAKING
• The motor is not plugged in.
•
The GFC I/ RCD cir cuit breaker is
tr ip ped.
•
Motor too hot a nd overload
protection
is shut off.
•
Improper chlorine or pH levels.
•
No filtering media in tank.
•
Wrong 6-way valve setting position.
•
Excess ively dirty pool.
•
The strainer screen is r es tri cti ng
the water flo w.
• Clogged inlet or discharge.
•
An air leak on the intake line.
• Excessively dirty pool.
•
Sa nd media clogged with dirt.
•
Nozzle and strainer connections
are reversed.
•
Crusting or caking on the fi lt ering
sand surface.
• P
oo l vacuuming device attached
to the system.
• In
let threaded air connector
con nected to the wrong hole on
the liner.
•
Low wa ter level.
•
St rai ner screen clogged up .
•
An air leak on the int ake hose.
• Faulty
moter or the impeller is
jammed.
• Sand tank o-ring miss ing.
•
Sa nd tank o-ring dirty.
•
Flange clamp not tight.
•
6-way valve damage .
•
Hose nut not secure ly tight.
•
Hose con nection fitting
o-ri
ng/L -s hape o-r ing missing.
•
Possib le inner timer defective.
Line cord must be plugged into a 3 wire outlet that is
protected by a Class A Ground Fault Ci r cu it Interrupter, or RCD .
Reset circuit breaker. If circuit breaker trips repeatedly , your
electrical system may have a defect. Tum off circuit breaker
and call an electrician to correct the problem.
L et the motor cool down and restart again.
• Adjust the chlorine and pH level. Consult your local
swimming pool supply stores.
• Load with filter sand, see "sand loading instructions".
• Set valve
to "FILTER" position.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Cl
ear any obstructions in the intake hose by discharging it
inside poo l wall.
Ti ghten hose nuts, check hoses for damage, check pool
water level.
• Clean the pre - filtering basket more often.
• Bac kwas h filter.
• Install the nozz le at the upper position of the pool i nlet , and
the strainer at the l ower position of the pool outlet.
Remove about 1" of sand if necessary .
•
Remove any pool vacuum i ng device attached to the
system line.
• Make sure the inlet threaded air connector is connected
to the pool in let upper hole .
• Fill pool
to correct water level.
•
Clea n strainer screens at poo l inlet.
•
Tighten hose nuts , check hose for damage.
• Contact lntex service center.
•
Remove 6-way val ve cover and ensure the
o-ring is in place.
•
Clean sa nd tank o-ring with ga rd en hose water.
•
Tighten secu rely.
•
Contact lntex service center.
• Tighten/reinstall
hose nut.
•
Ensur e o-r ing /L-sh ape o-ring is in place and not . ,.,,., .. "''"-.
damaged.
• Turn off the p ump and restart 5 minutes late r.
•
Re-set the timer.
•
Contact lnt ex serv i ce ce nt e r.
• Clogged inlet of the pre ss ur e gauge. • Clear a ny obstructions in the intake by
• Pressure gauge damag e. uns cr ew ing it from the 6-way valve.
•
Sa nd is too sma ll.
•
Sand bed is calcified.
•
Plunger valve not we ll-fitte d.
• Air jet valve is not tight and facing
up .
• A
ir jet valve internal seal blocked.
•
Air J et valve internal seal dirty.
•
Air jet valve broken.
•
Contact l nt ex service center.
•
Use on ly No. 20 silica sand with particle size
ran ge 0.45 to 0.85 mm (0.018 to 0.033 inch es)
and a Uniformity Coefficient less than 1.75.
• Change sand.
•
Tighten or re ins tall plunger va lve.
•
Tighten air jet valve and make sure it's facing
up.
• Turn pump ON and run for few seco nds, then
turn OFF, repeat 3 time s.
•
Remove air jet valve, flush dirt out wit h water
and replace valve back.
•
Replace a new air jet va lve.

Intex ECO20110-2 Specifications

General

Brand	Intex
Model	ECO20110-2
Category	Water Filtration Systems
Language	English