ll_-llil!+
Once you have adjusted the DAP modes and All Channel Stereo, the
adjustment is memorized for each source.
• You cannot use the DAP modes and All Channel Stereo if the rear
speakers are not connected or deactivated.
• You cannot adjust the effect level for "ALL CH STEREO."
From the remote control:
It will be convenient for you to use the remote control for adjustments,
since you can make adjustments from your listening point.
I Start playing 2 channel softwaremeither analog
or Linear PCMmand select the source.
2
Press SURROUND ON/OFF to ___c_
activate Surround mode. s
When Surround mode turns on, the last selected
Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
3
Press SURROUND MODE repeatedly +u_+ou+o
until one of the DAP modes--"LIVE
CLUB" "DANCE CLUB" "HALL"
"PAVILION"_or "ALL CH
STEREO" appears on the display.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4
5
Press SOUND.
The 10 keys are activated for sound adjustments.
%
6 For DAP modes only:
Press EFFECT to select the effect
level (1 to 5) you want.
• Each time you press the button, the effect
level changes as follows:
Adjust the speakers output levels - REAR-L+
(-10 to +10). Q _.__Q_
To
adjust the left rear speaker level, press x_-/_
REAR•L +/-. - REAR.R+
• TO adjust the fight rear speaker level, press Ov Q
REAR•R +/-.
For "ALL CH STEREO" only:
• To adjust the center speaker level, press -CENTER+
CENTER +1-. OAO
EFFECT
F EFFECT1 _ EFFECT2 _ EFFECT3 7
EFFECT5 _ EFFECT4 +_
As the number increases, selected mode becomes stronger
(normally set it to "EFFECT 3").
Onthefrontpanel:
I Start playing 2 channel software_either analog
or Linear PCM_and select the source.
2 Press SURROUND ON/OFF to so..oo.oo.,o,,
r...]
activate Surround mode.
When the Surround mode turns on, the last
selected Surround mode will be activated.
• Each time you press the button, Surround mode turns on and
off alternately.
3 Press SURROUND MODE sO..oo.oMOOE
repeatedly until one of the DAP
modes_"LIVE CLUB" "DANCE
CLUB" "HALL" "PAVILION"m
or "ALL CH STEREO" appears on the display.
The DSP indicator also lights up on the display.
If you like to adjust sound, go to step 4.
4 Adjust the speaker output levels.
I) Press ADJUST repeatedly until one
of the following indications (with the "_
current setting)* appears on the display.
REAR R :To adjust the fight rear speaker output level
(-10 to +10).
* "0" is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2) Press CONTROL UP A/DOWN • CO.T.OL
DOWN UP
to adjust the selected speaker [I II 7
output level.
3) Repeat steps I) and 2) to adjust
the other speaker level.
5 For DAP modes only: Adjust the effect level.
I) Press ADJUST repeatedly until Ao_osT
"EFFECT" (with the current _x_'_
setting)* appears on the display.
* "EFFECT 3" is the initial setting. If you have already
changed the setting, another setting will be shown.
Note:
2)
Press CONTROL UP • co.,.oL
DOWN UP
/DOWN • to select the effect level ii ,, _
t
(1 to 5) you want.
• Each time you press the button, the effect
level changes as follows:
F.ECT1 -- EFFECT2 -- EFFECT3 q
EFFECT 5 _ EFFECT 4
As the number increases, selected mode becomes stronger
(normally set it to "EFFECT 3").
You cannot select any DAP mode and All Channel Stereo when software
encoded with Dolby Digital or DTS Digital Surround is played back.
Tocancel DAPmodes and All Channel Stereo
Press SURROUND ON/OFF so that "SURROUND OFF" appears
on the display. The DSP indicator goes off.
23
/
gll
¢D
9_
Eo
o
gg
111
L
Ee
L
To Next Page
Loading...
Need help?
General
