Setting up the system
Connecting the system control
Preparing the remote control
Connecting system control cords after connecting a KENWOOD
audio component system lets you take advantage of convenient
system control operations.
Loading the batteries
0 Remove the cover. 0 Insert the batteries.
This unit is compatible only with the [SL-161 mode. The system
control operation is not available if the unit is connected in the
[XS81, [XSI, or [XRI connection mode.
If your component has the mode select switch, set the connected
components to the [SL161 mode.
c--
E
mlQ Q
SYSTEM CONTROL
cord
Q Close the cover.
l
Youmaycoi?nectthesystemcontrolcordtoeithertheupordown]ack
EXAMPLE: [SL161 mode connections
The underlllxd portlon represents the setting of the system control mode
E!351
I=1 [XSI IXS81 [XRI
[WI [XSI fXS81
Receiver
Cassette deck
B
SYSTEM
or MD recorder
CONTROL
cord
CD player
l
Insert two AA-size (R6) batteries as lndlcated by the polarity markings.
Operation
[XSI
piiizzy
l
In ordel to take advantage of the system control operations, the
components must be connected to the correct jacks. To use a CD
player It must be connected to the CD jacks. To use a cassette deck
(or MD recorder) it must be connected to the MD/TAPE lacks When
using Imore than one CD player (etc 1 only the one connected to the
speclfled jacks may be connected for system control
l
Some CD players and cassette decks are not compatible with the
lSL161 system control mode Do not make system connectlons with
equlplnent that IS not [SL161 compatible
l
Some MD players are not system control compatible You cannot
make system control connectlons to this kind of equipment.
When the STANDBY Indicator IS llt, the power turns ON when you press
the POWER IO) key on the remote control. When the power comes ON,
press the key you want to operate.
Operating range
WvW
i
f
Remote sensor
1
system
Notes
1 ISL161 eqtrlpment cannot be combined with [Xi?], IXSI, and IXSSI
equipment for systeln operations. If your equipment consists of
this kind of combination, please do not connect any system con-
trol cords Even wlthout system control cords, normal operations
can be carried out without effecting performance.
2 Do not connect system control cords to any components other
than those spectfled by KENWOOD It may cause a malfunction
and damage your equipment
3 Be sure the system control plugs are Inserted all the way in to the
system control tertnlnals
l
When pressing more than one remote control key successively, press
the keys securely by leaving an Interval of 1 second or more between
keys.
SYSTEM CONTROL OPERATIONS
Remote Control
Lets you operate this ul?lt with the system remote supplled with the
receiver
Automatic Operation
When you start playback from a source component, the Input selector
on this unit switches to that component automatlcally.
Synchronized Recording
Lets you synchrorxze recording with the start of playback when
recording from CD, MD or analog discs
Registering setup codes for KENWOOO audio components
If you own remote controllable KENWOOD audio components that
ale not compatible with system control, registering the setup code
enables you to control those components using the remote control
supplied wIti this unit (wIthout connecting system control cords) To
register setup codes for your remote controllable KENWOOD audio
components, see “Registering setup codes for other components”
Notes
1. The supplied batteries may have shorter lives than ordinary batteries
due to use during operation checks.
2 When the remote-controllable distance gets shorter than before, re-
place both batteries with new ones
3 Placlng the remote sensor in direct sunlIght, or in direct light from a
high frequency fluorescent lamp may cause a malfunction.
In such a case, change the location of the system installation to pre-
vent malfunction
17EN
To Next Page
Loading...
Need help?
General
