1. Introduction DVIDL-OPT series – User's Manual 6
Typical Applications
LC 50/125 MULTIMODE
LASER ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L. A.
OUT 1A OUT 1B
OUT 2A OUT 2B
OUT 3A OUT 3B
OUT 4A OUT 4B
LC 50/125 MULTIMODE
LASER ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L.ACTIVE
L. A.
OUT 1A OUT 1B
OUT 2A OUT 2B
OUT 3A OUT 3B
OUT 4A OUT 4B
4 CH DUAL LINK DVI INPUT BOARD
MX-DVIDL-IB
4 CH DUAL LINK DVI INPUT BOARD
MX-DVIDL-IB
PIN: 2.35mm
5V 1.5A DC
OUTPUT
FIBER INPUT
Fiber INPUT A: CLK: TMDS 3,4,5 (Link 2)
Fiber INPUT B: CLK: TMDS 0,1,2 (Link 1)
Made in
For single link DVI signal use Fiber link 1 only.
For dual link DVI extension use both Link 1 and Link 2.
Link 1: Fiber output A Fiber Input B
Link 2: Fiber output B Fiber input A
DVIDL-OPT-RX100
PIN: 2.35mm
5V 1.5A DC
OUTPUT
FIBER INPUT
Fiber INPUT A: CLK: TMDS 3,4,5 (Link 2)
Fiber INPUT B: CLK: TMDS 0,1,2 (Link 1)
Made in
For single link DVI signal use Fiber link 1 only.
For dual link DVI extension use both Link 1 and Link 2.
Link 1: Fiber output A Fiber Input B
Link 2: Fiber output B Fiber input A
DVIDL-OPT-RX100
OUTPUT2
-4dB loss
OUTPUT2
-4dB loss
INPUT OUTPUT
INPUT
Neutrik OpticalCON
Duo hybrid
Duo hybrid
Neutrik OpticalCON
Duo hybrid
DVIDL-OPT-RX100
DVIDL-OPT-RX100
Projector
Dual-Link
Dual-Link
DVI
Dual-Link
DVI
Dual-Link PC
MX-FR17
SP2OPT-NT
MX-DVIDL-OPT-OB-NT
MX-DVIDL-OPT-OB-NT
MX-DVIDL-IB
MX-DVIDL-IB
Integrated System Diagram
PIN: 2.35mm
5V 1.5A DC
OUTPUT
FIBER INPUT
Made in
DVIDL-OPT-TX200
Universal EDID Detailed Timings
1920X1200P@60
2048X1080P@60
1920X1080P@60
EDID STATUS FUNCTIONS
RED: INVALID EDID MEMORY
GREEN: VALID EDID SELECTED
For single link DVI signal use Fiber link 1 only.
For dual link DVI extension use both Link 1 and Link 2.
Link 1: Fiber output A Fiber input B
Link 2: Fiber output B Fiber input A
Fiber OUTPUT A: CLK; TMDS 0,1,2 (Link 1)
Fiber OUTPUT B: CLK; TMDS 3,4,5 (Link 2)
PIN: 2.35mm
5V 1.5A DC
OUTPUT
FIBER INPUT
Fiber INPUT A: CLK: TMDS 3,4,5 (Link 2)
Fiber INPUT B: CLK: TMDS 0,1,2 (Link 1)
Made in
For single link DVI signal use Fiber link 1 only.
For dual link DVI extension use both Link 1 and Link 2.
Link 1: Fiber output A Fiber Input B
Link 2: Fiber output B Fiber input A
DVIDL-OPT-RX100
Neutrik OpticalCON
Duo hybrid up to 2500m
DVIDL-OPT-TX200
DVIDL-OPT-RX100
Dual-Link PC Local Monitor Dual-Link Projector
Dual-Link
DVI
Dual-Link
DVI
Dual-Link
DVI
Standalone Application Diagram
Supports 4K Resolutions
Transmitting Dual-Link video signals up to 4096x2400
resolution, including all standard HDTV resolutions.
Unencrypted signals up to 330 MHz pixel clock
frequency (up to 165 MHz TMDS clock frequency).
high-speed TMDS data lanes are transmitted using
eliminates its inherent weakness, guaranteeing a safe,
dust protected, and durable connection.
switched signal. There is no frame or line period delays
to the signals when passing a Lightware router.
Advanced EDID Management
The user can emulate any EDID on the inputs
independently, read out and store any attached
monitor's EDID in 100 internal memory locations.
Galvanic Isolation between Source and Display
transmitter and receiver to eliminate ground loop noise
or HUM effects.
LED1
LED2
LED3
Source-, signal-, monitor- and laser detection, to get
immediate feedback about the status of connected
devices.
USB Control
information can be accessed with Lightware Device
Controller software via USB connection. Firmware
upgrade can also be performed over this interface.
Locking DC Connector
Special locking plug of wall adaptor ensures safe power
supply. This type of connector prevents accidental
disconnections.
0
1
2
3
4
5
6
7
8
9
EDID address selection with two decimal rotary
switches and LEARN button are available for Advanced
EDID Management.
The user can attach a local monitor to observe the
resolution and clock frequency are the same on DVI
Removes jitter caused by long cables; the output has
a clean, jitter free signal, eliminating signal instability
and distortion caused by long cables or connector
To Next Page
Loading...
Need help?
General