Mitsubishi UD8350 User Manual

EN-50
6. Enter the NEW NETWORK PASSWORD and
CONFIRM NETWORK PASSWORD.
• Passwordcanbesetusingupto32characters
including alphabets (capital/small) or numeric
characters.
← key: ............. Shifting the position of enter
cursor to the left for each
character.
→ key: ............. Shifting the position of enter
cursor to the right for each
character.
key: ............... Shifting the position of
enter cursor between NEW
NETWORK PASSWORD
and CONFIRM NETWORK
PASSWORD.
DEL key: .......... Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key: Switching an alphabet character
to CAPITAL or small.
CLEAR key: ..... Deleting all the entered
characters.
• Youcanenternumbersbypressingthenumber
buttons (0 to 9) while holding down the NUM
button on the remote control.
7. When NEW NETWORK PASSWORD and CONFIRM
NETWORK PASSWORD are matched, the setting
is completed after changing the NETWORK
PASSWORD.
• WhenyouselectOKandthepasswordsyou
entered are matched, the setting change dialog
is displayed. After the dialog disappears, the
NETWORK menu is displayed.
• WhenyouselectCANCEL,theNETWORKmenu
is displayed without changing the password.
• Iftheenteredcontentisnotmatched,NEW
NETWORK PASSWORD screen appears again
after an error dialog is displayed.
• Itmaytakesometimetoreectthesettings.
IP Settings
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or  button to select IP CONFIG.
IP CONFIG
ENTER
3. Press the ENTER button.
• IPCONFIGmenuappears.
NETWORK
IP CONFIG
1 2
opt.
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
0. 0. 0. 0
0. 0. 0. 0
0. 0. 0. 0
MAC ADDRESS
12
ON
Initial network settings (continued)
Setting or Clearing DHCP
1. Display the IP CONFIG menu.
2. Press the  or  button to select DHCP.
DHCP
ON
3. Press the ENTER button.
• Conrmationdialogappears.
DHCP :
OK : ENTER CANCEL : MENU
ON
4. Press the  or  button to select ON or OFF .
5. Press the ENTER button.
• WhenyouselectOK,thesettingchangedialog
is displayed. After the dialog disappears, the
NETWORK menu is displayed.
• Tocancelthesetting,presstheMENUbutton.
• Itmaytakesometimetoreectthesettings.
• WhensettingDHCPtoON,IPADDRESS,
SUBNET MASK, and DEFAULT GATEWAY
cannot be set. If you set those settings, set
DHCP to OFF and perform the IP settings as the
following procedures.
IP Address Settings
1. Display the IP CONFIG menu.
2. Press the  or  button to select IP ADDRESS.
IP ADDRESS
0. 0. 0. 0
3. Press the  or  button to select SET .
4. Press the ENTER button.
• IPADDRESSscreenappears.
IP ADDRESS
192 . 168 . 0 . 10
0
OK
CLEAR
DEL
CANCEL
1234567 8 9
← →
5. Press the direction buttons to move the key cursor,
select the numbers to enter, and press the ENTER
button.
• Setthenumericvaluewithintherangefrom0to
255. However, set the numeric value for the final
octet within the range from 1 to 254.
← key: Shifting the position of enter cursor to
the left.
→ key: Shifting the position of enter cursor to
the right.
DEL key: Deleting the character in the position
of enter cursor for each character.
CLEAR key: Deleting all the entered
characters.
• Youcanenternumbersbypressingthenumber
buttons (0 to 9) while holding down the NUM
button on the remote control.

Mitsubishi UD8350 Specifications

General

Brand	Mitsubishi
Model	UD8350
Category	Projector
Language	English