Oki ML3410 User Manual

Specifications
Specifications
Printhead:
9 pin
Print speed @ 10 cpi:
HSD 550 cps Utility 417 cps NLQ 104 cps
Emulations:
Epson FX/IBM ProPrinter, co-resident Pacemark/Microline, by means of optional chip
set
Interface:
Parallel and RS232C serial, standard Optional Twin-Ax/Co-Ax (3rd partycall
1-800-OKIDATA for information)
Graphics resolution:
1445216 dpi maximum
Fonts:
NLQ: Courier, Gothic, Proportional Draft: Utility, High Speed Bar Code: UPC-A, UPC-E,
EAN 8, EAN 13, Code 3 of 9, Interleaved 2 of 5
Buffer size:
64K
Reliability:
Mean Time Between Failures (MTBF) 8,000 hours at 25% duty cycle, 35% page
density Mean Time To Repair (MTTR) 15 minutes Printhead life 200 million characters average in
10 cpi utility mode
Paper Specifications:
Weight 12 to 24 lb. Thickness Top feed: 0.36 mm (0.014 inches) maximum
Bottom feed: 0.50 mm (0.020 inches) maximum
Continuous forms:
Types Interleaved: original plus 5 copies Carbonless: original plus 7 copies
Width 3.5 to 16.5 inches
Cut sheet multi-part forms:
Original plus 3 copies (top edge must be glued tight)
Labels:
Carrier width 3.5 to 16.5 inches wide Use bottom feed only.
Envelopes:
Weight 24-lb. maximum Size Minimum 6.5 5 3.6 inches Maximum 9.5 5 4.1 inches
Feed: Single feed Continuous feed overlap type only
Card stock:
120-lb. maximum Use bottom feed only.
Transparencies:
Use top feed only.
Dimensions:
Width 25-1/4 inches (540 mm) Depth 19 inches (483 mm) Height 15 inches (203 mm)
Weight 63 lbs. (25.4 kg)
Environmental Requirements:
Operating Temperature 50 to 104 degrees F (10 to 40 degrees C)
Storage Temperature 14 to 122 degrees F (-10 to +50 degrees C) Humidity 20 to 80% RH
Electrical Requirements:
Voltage 120 volts, +5.5%/-15% 220/240 volts, ±10% Frequency 50/60
Hz, ±2 Hz Power Idling: 30 watts Operating: 75 watts
Specifications subject to change without notice
ML3410 ( 96-02-07 )

Oki ML3410 Specifications

Print Specifications

printhead	9 pin
print speed at 10 cpi	HSD 550 cps, Utility 417 cps, NLQ 104 cps
graphics resolution	1445216 dpi maximum

Paper Handling

paper weight	12 to 24 lb
paper thickness top feed	0.36 mm (0.014 inches) maximum
paper thickness bottom feed	0.50 mm (0.020 inches) maximum

Operating Environment

operating temperature	50 to 104 degrees F (10 to 40 degrees C)
storage temperature	14 to 122 degrees F (-10 to +50 degrees C)
humidity	20 to 80% RH

Electrical Requirements

voltage	120 volts, +5.5%/-15% 220/240 volts, ±10%
frequency	50/60 Hz, ±2 Hz
power idling	30 watts
power operating	75 watts

Weight and Dimensions

width	25-1/4 inches (540 mm)
depth	19 inches (483 mm)
height	15 inches (203 mm)
weight	63 lbs. (25.4 kg)