61
En
09
Using other functions
Switching the speaker
terminals
If you selected 9.1ch FH/FW,
7.1ch + Speaker B, 7.1ch FH/FW + ZONE 2 or
5.1ch + SP-B Bi-Amp at Speaker system setting
on page 87, you can switch between speakers
using the SPEAKERS button.
If you selected 7.1ch Front Bi-Amp,
7.1ch + ZONE 2, 5.1ch Bi-Amp + ZONE 2,
5.1ch + ZONE 2+3, 5.1ch F+Surr Bi-Amp
or 5.1ch F+C Bi-Amp, the button will simply
switch your main speaker terminals on or off.
% Use SPEAKERS on the front panel to
select a speaker system setting.
As mentioned above, if you have selected
7.1ch Front Bi-Amp, 7.1ch + ZONE 2,
5.1ch Bi-Amp + ZONE 2, 5.1ch + ZONE 2+3,
5.1ch F+Surr Bi-Amp or 5.1ch F+C Bi-Amp,
the button will simply switch your main speaker
terminal (A) on or off.
Press repeatedly to choose a speaker terminal
option:
When you select 9.1ch FH/FW, you can select
from:
! SP: FH/FW ON – Front height or front wide
channels are added to the front, center,
surround and surround back channels
(maximum 7 channels) and a maximum of 9
channels are output. The front height and front
wide channels are switched automatically
according to the audio input signal.
! SP: FH ON – Front height channels are added
to the front, center, surround and surround
back channels (maximum 7 channels) and a
maximum of 9 channels are output.
! SP: FW ON – Front wide channels are added
to the front, center, surround and surround
back channels (maximum 7 channels) and a
maximum of 9 channels are output.
! SP: OFF – No sound is output from the
speakers.
When you select 7.1ch + Speaker B, you can
select from:
! SP: A ON – Sound is output from the
A-speaker terminals (up to 9 channels
(including front height channels), depending
on the source).
! SP: B ON – Sound is output from the two
speakers connected to the B-speaker
terminals. Multichannel sources will not be
heard.
! SP: A+B ON – Sound is output from the
A-speaker terminals (up to 7 channels,
depending on the source), the two speakers
connected to the B-speaker terminals, and
the subwoofer. The sound from the B-speaker
terminals will be the same as the sound
from the A-speaker terminals (multichannel
sources will be downmixed to 2 channels).
! SP: OFF – No sound is output from the
speakers.
When you select 7.1ch FH/FW + ZONE 2, you
can select from:
! SP: FH/FW ON – Front height or front wide
channels are added to the front, center and
surround channels (maximum 5 channels)
and a maximum of 7 channels are output.
The front height and front wide channels are
switched automatically according to the audio
input signal.
! SP: FH ON – Front height channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
! SP: FW ON – Front wide channels are added
to the front, center and surround channels
(maximum 5 channels) and a maximum of 7
channels are output.
! SP: OFF – No sound is output from the
speakers.
When you select 5.1ch + SP-B Bi-Amp, you can
select from:
! SP: A ON – Sound is output from the
A-speaker terminals (maximum 5 channels).
! SP: B ON – Sound is output from the two
speakers connected to the B-speaker
terminals. Multichannel sources will not be
heard.
! SP: A+B ON – Sound is output from the
A-speaker terminals (up to 5 channels,
depending on the source), the two speakers
connected to the B-speaker terminals, and
the subwoofer. The sound from the B-speaker
terminals will be the same as the sound
from the A-speaker terminals (multichannel
sources will be downmixed to 2 channels).
! SP: OFF – No sound is output from the
speakers.
Note
! When 7.1ch + Speaker B or
5.1ch + SP-B Bi-Amp is selected for the
Speaker System setting (page 87) and the
Speaker B Link setting (HDMI Setup on page
54) is turned on, the setting of the played
speaker terminals switches automatically
when HDMI OUT is switched. For details, see
Switching the HDMI output on page 62.
! The subwoofer output depends on the settings
you made in Manual speaker setup on page
87. However, if SP: B ON is selected above, no
sound is heard from the subwoofer (the LFE
channel is not downmixed).
! All speaker systems (except
7.1ch + Speaker B connections) are switched
off when headphones are connected.
Using the MULTI-ZONE controls
The following steps use the front panel con-
trols to adjust the sub zone volume and select
sources. See MULTI-ZONE remote controls on
page 62.
1 Press MULTI-ZONE ON/OFF on the
front panel.
Each press selects a MULTI-ZONE option:
! ZONE 2 ON – Selects your primary (ZONE 2)
sub zone
! ZONE 2&3 ON – Select both sub zones
! ZONE 3 ON – Selects your secondary
(ZONE 3) sub zone
! MULTI ZONE OFF – Switches the MULTI-
ZONE feature off
The MULTI-ZONE indicator lights when the
MULTI-ZONE control has been switched ON.
2 Press MULTI-ZONE CONTROL on the
front panel to select the sub zone(s) you
want.
If you selected ZONE 2&3 ON above, you can
toggle between ZONE 2 and ZONE 3.
! When the receiver is on, make sure that any
operations for the sub zone are done while
ZONE and your selected sub zone(s) show in
the display. If this is not showing, the front
panel controls affect the main zone only.
If the receiver is in standby, the display is
dimmed, and ZONE and your selected sub
zone(s) continue to show in the display.
3 Use the INPUT SELECTOR dial to select
the source for the zone you have selected.
For example, ZONE 2 DVD sends the source
connected to the DVD inputs to the primary
(ZONE 2) sub room.
! If you select TUNER, you can use the tuner
controls to select a preset station (see Saving
station presets on page 41 if you’re unsure
how to do this). The tuner cannot be tuned to
more than one station at a time. Therefore,
changing the station in one zone also
changes the station in the other zone. Please
be careful not to change stations when
recording a radio broadcast.
4 When Speaker System is set to
7.1ch + ZONE 2, use the MASTER VOLUME
dial to adjust the volume for the sub zone.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
