A call partner says that the volume is too low
or high.
Adjust the volume accordingly using Mic Gain
adjustment (page 18).
Echo or noise occurs in phone call
conversations.
• Lower the volume.
•
If
the ambient noise other than the phone call sound
is
loud, try reducing this noise.
E.g.:
If
a window
is
open and road noise, etc.,
is
loud,
shut the window.
If
the air conditioner
is
loud, lower
the air conditioner.
The phone is not connected.
When the Bluetooth audio
is
played back, the phone is
not connected even if you press
~
(handsfree
).
--+
Connect from the phone.
The phone sound quality is poor.
Phone sound quality depends on reception conditions
of
cellular phone.
--+
Move your car to a place where you can enhance
the cellular phone's signal ifthe reception
is
poor.
The volume of the connected audio device is
low (high).
Volume level will differ depending on the audio
device.
--+
Adjust the volume
of
the connected audio device or
this unit.
The sound skips during playback of a
Bluetooth audio device.
• Reduce the distance between the unit and the
Bluetooth audio device.
•
If
the Bluetooth audio device is stored
in
a case
which interrupts the signal, remove the audio device
from the case while using.
• Several Bluetooth devices
or
other devices which
emit radio waves are used nearby.
--+
Turn off the other devices.
--+
Reduce the distance from the other devices.
• The playback sound stops momentarily when the
connection between this unit and the cellular phone
is
being made. This is not a malfunction.
The connected Bluetooth audio device cannot
be controlled.
Check that the connected Bluetooth audio device
supports
AVRCP.
Some functions do not work.
Check if the connecting device supports the functions
in
question.
A call is answered unintentionally.
The connecting phone
is
set to answer a call
automatically.
No sound is output from the car speakers
during handsfree call.
If
the sound is output from the cellular phone, set the
cellular phone to output the sound from the car
speakers.
"OFF BT" appears when initializing.
Press and hold
(BT)
until"
0 "turns off. Then
initialize again (page
19).
The external microphone does not work.
The setting
of
the microphone
is
not correct.
--+
Set "MIC-EXT" (page 20).
Error displays/Messages
CHECKING
The unit
is
confirming the connection
of
a USB device.
--+
Wait until confirming the connection
is
finished.
ERROR*1
• The disc
is
dirty or inserted upside down.
*2
--+
Clean or insert the disc correctly.
• A blank disc has been inserted.
• The disc cannot play due to a problem.
--+
Insert another disc.
• USB device was not automatically recognized.
--+
Reconnect
it
again.
• Press
~
to
remove the disc.
FAILURE (Illuminates until any button
is
pressed.)
The connection
of
speakers/amplifiers
is
incorrect.
--+
See the installation guide manual
of
this model to
check the connection.
FAILURE (Illuminates for about I second.)
When the SAT tuner
is
connected, storing an SAT
radio channel into a preset failed.
--+
Be sure to receive the channel that you want to
store, then try it again.
HUB NO SUPRT
USB hub
is
not supported on this unit.
LOAD
The CD changer
is
loading the disc.
--+
Wait until loading is complete.
L.
SEEK+/-
The local seek mode
is
on during automatic tuning.
NO DEV (No Device)
(
SOURCE)
is
selected without a USB device
connected. A USB device or a USB cable has been
disconnected during playback.
--+
Be sure to connect a USB device and USB cable.
NO DISC
The disc
is
not inserted
in
the CD changer.
--+
Insert discs
in
the
CD
changer.
NO MAG
The disc magazine
is
not inserted
in
the CD changer.
--+
Insert the disc magazine
in
the CD changer.
NO MUSIC
The disc or USB device does not contain a music file.
--+
Insert a music CD
in
this unit or an MP3 playable
CD changer.
--+
Connect a
USB
device with a music file in it.
NO NAME
A disc/album/artist/track name
is
not written
in
the
track.
continue to next page
--+
-
29
To Next Page
Need help?
General
Weight and Dimensions
