Charging the battery pack
When using the camera for the first time, be sure to charge the NP-FW50
“InfoLITHIUM” battery pack (supplied).
The “InfoLITHIUM” battery pack can be charged even when it has not been
fully depleted. It can also be used when it has not been fully charged.
• The charging time differs depending on the remaining capacity of the battery pack
or charging conditions. The above charging time is when charging a fully depleted
battery pack at a temperature of 25 °C (77 °F).
• We recommend charging the battery pack in an ambient temperature of between
10 °C and 30 °C (50 °F and 86 °F) to efficiently charge the battery pack.
• Connect the battery charger to the nearest wall outlet (wall socket).
Inserting the charged battery pack
x
Removing the battery pack
Inserting a memory card (sold separately)
x
Memory cards that you can use
You can use following types of memory cards with this camera. However,
proper operation cannot be guaranteed for all types of the memory cards.
You cannot use MultiMediaCard.
x
Removing the memory card
Open the cover, make sure that the access lamp is not lit, and push the memory
card once.
• When the access lamp is lit, do not remove the memory card or the battery pack, or
turn off the power. The data may be corrupted.
Attaching/removing the lens
Set the power switch of the camera to OFF before you attach or remove the
lens.
• When attaching a lens, do not press the lens release button.
• Do not use force when attaching a lens.
• The Mount Adaptor (sold separately) is required to use an A-mount lens (sold
separately). For details, refer to the operating manual supplied with the Mount
Adaptor.
x
Removing the lens
• When changing the lens, if dust or debris gets inside the camera and adheres to the
surface of the image sensor (the part that acts as the film), it may appear as dark
spots on the image, depending on the shooting environment. The camera vibrates
slightly when it is turned off, due to the anti-dust function, to prevent dust from
adhering to the image sensor. However, attach or remove the lens quickly
somewhere away from dusty locations.
Setting up the date
When you turn on the camera for the first time, the screen to set date and time
appears.
1
Insert the battery pack onto the
battery charger, and charge it.
• The CHARGE lamp turns off when
charging is finished.
For the U.S.A and Canada
CHARGE lamp
For countries/regions other
than the U.S.A. and Canada
Power cord (mains lead)
Notes
1
Open the cover, and insert the
battery pack.
• Insert the battery pack while
pressing the lock lever with the tip
of the battery.
Lock lever
2
Close the cover.
Turn off the camera, make sure that the
access lamp is not lit, slide the lock lever
in the direction of the arrow, and pull out
the battery pack.
1
Insert a memory card with the
direction as illustrated here.
• Insert the memory card until it
clicks as illustrated.
Check on the direction of the
notched corner.
Estimated charging
time
250 minutes
CHARGE lamp
Access lampLock lever
Usable memory card Still
image
Movie Term in this
manual
“Memory Stick PRO Duo”
media
(Mark2) “Memory Stick
PRO Duo” media
“Memory Stick PRO-HG
Duo” media
SD memory card (Class 4 or more) SD card
SDHC memory card (Class 4 or more)
SDXC memory card (Class 4 or more)
1
Mount the lens by aligning the
white index marks on the lens
and the camera.
• Hold the camera’s face downward
to prevent the dust from entering
into the camera.
White index marks
2
While pushing the lens lightly
toward the camera, turn the
lens clockwise until it clicks
into the locked position.
Notes
1
Press the lens release button
all the way in and turn the lens
counterclockwise until it
stops.
Lens release button
Notes
1
Set the power switch to ON to turn on the camera.
The screen to set date and time appears.
To Next Page
Loading...
Need help?
General
