EasyManua.ls Logo

Sony SNC-CH110 User Manual

Sony SNC-CH110
97 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #48 background imageLoading...
Page #48 background image
Administrating the Camera
Configuring the Network — Network Menu
48
Note
The model on sale in China does not support
CRAM-MD5 authentication.
User name, Password
Type the user name and password of the owner of the
mail account, using up to 64 characters. This setting is
necessary when the SMTP server that sends e-mails
performs authentication.
Recipient e-mail address
Type the recipient e-mail address, using up to 64
characters. You can specify only one recipient e-mail
address.
Administrator e-mail address
Type the e-mail address of the camera administrator,
using up to 64 characters. This is used as the reply
address or the address for a system mail from the mail
server.
Subject
Type the subject/title of the e-mail, using up to 64
characters.
Message
Type the text of the e-mail using up to 384 characters. (A
line break is equivalent to 2 characters.) You can
describe the information of the acquired IP address, etc.,
using the special tags mentioned below.
HTTP notification
Select On to output a command to the HTTP server
when the DHCP setting is completed. Using this
function, you can configure a useful system, for
example, to view the access log stored in the HTTP
server, or start an external CGI program.
URL
Specify the URL to send an HTTP request, using up to
256 characters. The URL is normally written as follows:
ip_address: Type the IP address or host name of the host
to which you want to connect.
To enter an IPv6 address:
http:// [IPv6 address]
http:// [IPv6 address]: port
[:port]: Specify the port number to which you want to
connect. If you want to use the established port
number 80, you do not need to input a value.
path: Type the command.
parameter: Type the command parameter if necessary.
You can use the special tags mentioned below for the
parameters.
Proxy server name
When you send an HTTP request via a proxy server,
type the name or IP address of the proxy server, using up
to 64 characters.
Proxy port number
Specify the port number when you send an HTTP
request via the proxy server. Set a port number between
1024 and 65535.
Method
Select the HTTP method GET or POST.
OK/Cancel
See “Buttons common to every menu” on page 32.
About the special tags
You can use the following five special tags to allow
notification of the settings acquired by DHCP, such as an
IP address. Type the tags in the parameter section of the
URL that you described in the Message field of the
HTTP.
<IP>
Use this tag to embed the IP address acquired by DHCP
in the text or parameter.
<HTTPPORT>
Use this tag to embed the specified HTTP server port
number in the text or parameters.
<MACADDRESS>
Use this tag to embed the MAC address of the interface,
whose IP address was acquired by DHCP, in the text or
parameter.
<MODELNAME>
Use this tag to embed the camera’s model name in the
text or parameter.
<SERIAL>
Use this tag to embed the camera’s serial number in the
text or parameter.

Table of Contents

Other manuals for Sony SNC-CH110

Question and Answer IconNeed help?

Do you have a question about the Sony SNC-CH110 and is the answer not in the manual?

Sony SNC-CH110 Specifications

General IconGeneral
Maximum resolution1280 x 960 pixels
Video formats supportedH.264
Analog signal format systemNTSC, PAL
White balanceAuto, Manual
Camera shutter speed1/2 - 1/10000 s
Minimum illumination5 lx
Sensor typeCMOS
Optical sensor size1/3.8 \
Video motion detectionYes
Cabling technology10/100Base-T(X)
Supported network protocolsIPv4, IPv6, TCP, UDP, ARP, ICMP, IGMP, HTTP, HTTPS, FTP (client), SMTP, DHCP, DNS, NTP, RTP/RTCP, RTSP, SNMP (MIB-2)
Dimensions (WxDxH)44 x 93 x 44 mm
Networking featuresEEE802.1X
Compatible operating systemsWindowsXP, WindowsVista (32bit), Windows7 (32bit)
Power source typePoE
Power consumption (typical)2.4 W
Minimum RAM1024 MB
Compatible memory cardsSD
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 50 °C
CertificationUL2044, FCC 15B Class B, IC Class B, IEC60950-1, EN55022(B)+EN55024+EN50130-4, VCCI Class B, C-Tick Class B
Weight and Dimensions IconWeight and Dimensions
Length93 mm
Weight100 g
Diameter44 mm

Summary

Introduction and Setup

Product Overview and Features

Details key features and capabilities of the network camera, including image quality and supported modes.

User Guide and System Requirements

Guidance on using the manual, system requirements, and installation manual overview.

Camera Preparation and IP Assignment

Steps for initial camera setup, including assigning an IP address using SNC toolbox or ARP commands.

Camera Operation and Access

Accessing the Camera via Web Browser

Instructions for accessing the camera's live view and controls through a web browser.

Administrator and User Roles

Defines Administrator and User roles, detailing access rights and available functions for each.

Logging into the System

Procedures for logging into the camera system as a user, including viewer options.

Main Viewer Interface and Controls

Explains the main viewer components, controls, and how to configure display settings.

Advanced Camera Administration

Administrator Menu and Setup Guide

Guide to accessing and navigating the Administrator menu for camera setup.

System, Date/Time, and Network Configuration

Covers system settings, date/time synchronization, and network connection configurations.

Camera Image, Video, and Streaming Settings

Details settings for image quality, video codec, day/night mode, and streaming.

Security, Authentication, and User Management

Configuration of SSL, 802.1X authentication, user accounts, and security policies.

Event Handling and Utility Tools

Image Sending and Trigger Functions

Setup for sending images via email (SMTP) and FTP, and configuring trigger actions.

Event Detection and Motion Monitoring

Configuration of sensor inputs, camera tampering detection, and motion detection.

SNC Toolbox and Device Management

Using SNC toolbox for device registration, firmware upgrades, and scheduled tasks.

Glossary of Terms

Definitions of technical terms and acronyms used in the manual.

Related product manuals