STIEBEL ELTRON DCE 11/13 User Manual

OPERATION
Appliance description
22 |DCE 11/13| DCE 11/13 RC| DCE 11/13 H www.stiebel-eltron.com
2.3 Test symbols
See type plate on the appliance.
3. Appliance description
The electronically controlled compact instantaneous water heater
maintains a constant outlet temperature up to its output limit,
irrespective of the inlet temperature.
The appliance warms the water directly at the draw-off point, as
soon as you turn on the hot water tap. The short pipe runs ensure
that energy and water losses are minimal.
For the start flow rate, see "Installation/ Specification/ Data
table".
The DHW output depends on the cold water temperature, the
heating output, the flow rate and the set temperature required.
DHW temperature
The DHW outlet temperature can be variably adjusted.
Heating system
The bare wire heating system is suitable for hard and soft water
areas. This heating system has a low susceptibility to scale build-
up. The heating system ensures quick and efficient DHW provision.
Note
The appliance is equipped with an air detector that large-
ly prevents damage to the heating system. If, during op-
eration, air is drawn into the appliance, the heater shuts
down automatically for one minute, thereby protecting
the heating system.
4. Settings
4.1 DCE11/13 | DCE11/13H
Operation
°C
40
50
60
30
20
D0000039989
1
1 Temperature selector: Temperature setting range
20°C– 60°C
4.2 DCE 11/13 RC
With the wireless remote control, the temperature setting can
be adjusted by wireless control. The selected temperature is dis-
played on the remote control.
The wireless remote control provided is registered to the receiver
module. Only a registered remote control can alter the settings
on the appliance.
The wireless range is reduced by obstacles between the appliance
and the remote control.
You can mount the wireless remote control anywhere using the
wall mounting bracket supplied in the standard delivery.
Operation
1
+
-
2
D0000039990
2
1
3
1 Display
2 Temperature selection 20°C – 60°C in 0.5°C steps, using the
+ and - buttons
3 Memory keys 1 and 2
The wireless remote control is normally in power save mode,
which means the display is switched off. Pressing any key activates
the wireless remote control, the temperature display appears. The
progress bar indicates that data is being transmitted to the device.
If no key is pressed within 10seconds the wireless remote control
automatically switches back to power save mode.
The selected temperature is also maintained in power save mode.
Saving temperature to memory keys
 Select the required temperature.
 Press memory key 1 or 2 for 2seconds. The temperature dis-
play flashes once to confirm.
 The heater of the appliance can be switched off (display
message OFF). To switch the heater off, select the minimum
temperature (20°C), then press the "-" button once.
Battery change
1
+
-
2
D0000047484
1
1 Battery change symbol
When the battery symbol illuminates, change the battery of the
wireless remote control. A change of battery may also become

STIEBEL ELTRON DCE 11/13 Specifications

General

Brand	STIEBEL ELTRON
Model	DCE 11/13
Category	Water Heater
Language	English

Summary

Special Information and Overviews

Operation Section Overview

Introduction to the operation chapter and its scope.

Installation Section Overview

Introduction to the installation chapter and its scope.

Operating Your Water Heater

General Operation, Safety, and Symbols

Essential general information, safety instructions, and symbols for safe operation.

Appliance Description and Settings

Details on the appliance's features, test symbols, and how to adjust settings.

Cleaning, Maintenance, and Troubleshooting

Guidance on cleaning, regular maintenance, and resolving common operational issues.

Installing Your Water Heater

Installation Safety and Preparations

Crucial safety instructions, standards, regulations, and preparatory steps for installation.

Minimum Clearances and Site Requirements

Requirements for the installation location and minimum clearances for safe operation.

Standard Installation and Connections

Step-by-step instructions for standard appliance installation and making connections.

Commissioning, Shutdown, and Options

Guide for start-up, handover, shutdown, and advanced installation options.

Anti-scalding, Power Conversion, and Troubleshooting

Configuring anti-scalding, power conversion, and troubleshooting installation issues.

Diagnostic Troubleshooting Lights

How to diagnose and troubleshoot installation-related issues using LED indicators.

Maintenance and Technical Data

Wireless Remote Control and Parts Maintenance

Managing the wireless remote control and maintaining key components like strainers.

Appliance Dimensions and Wiring

Detailed dimensions, wiring diagrams, and application areas of the appliance.

Performance Data and Energy Consumption

Information on mixed water, pressure drop, fault conditions, and energy usage.

Comprehensive Data Table

A detailed table listing all technical specifications and electrical data.

Product Guarantee and Warranty

Warranty Terms by Region

Details on guarantee conditions applicable based on the region of appliance purchase.

Environmental Compliance and Disposal

Eco-Design and Material Disposal Guidelines

Information regarding eco-design regulations and proper disposal of the appliance materials.