SystemAir SysAqua 25 Regulation Manual

English
Tu-Su
Tu-Fr
Mo to
1/3
Low load
Reduced
On
Off
1/4
Off
*:*
Off
22:00
On
14:00
Low load
11:00
On
07:00
Off
00:00
Value 6
Time 6
Value 5
Time 5
Value 4
Time 4
Value 3
Time 3
Value 2
Time
Value 1
1
1/12Monday
Off
Off
Off
On
On
On
On
Mo to
Off
On
Exception
Sunday
Saturday
Friday
Thursday
Wednesday
Tuesday
Copy schedule
Monday
1/10Schedule
50 %
Low load lim.
1/1Load Shedding
Eco+low noise
Low noise
Eco
Decreased cool. setp
1/4
2.0 bar
2.0 bar
2.0 bar
2.0 bar
3.0K
3.0K
2.0K
-P. cond. delta
-P. evp. delta
-Circuit 2
-P. cond. delta
-P. evp. delta
-Circuit 1
Low noise
-Wat.t.eco sh.H
-Wat.t.eco sh.C
Eco mode
-Wat.t.night sh.C
Decreased cool. setp
Decreased cool. setp
Reduced mode type
1/17Reduced mode
Enable
Disable
1/2
40.0 °C
20.0 °C
45.0°C
6.0dK
30.0°C
0.0dK
10.0°C
Disable
-Heating T.
-Minimum setpoint
-Setpoint at 0°C
Heating mode
-SH setpoint high
-Outs. temp. high
-SH setpoint low
-Outs. temp. low
Cooling mode
Compensation
1/12
Water Law
5K
20°C
S/W hysteresis
Auto Setpoint
1/2Auto change over
Cloud
Lon
BACnet MSTP
BACnet IP
Modbus
Ethernet
1/6Communication overview
Français
Deutsch
English
1/3
English
Français
English
SMS language
+Modem
Save -> SD
+Alarm-snapshot
HMI Language
1/5Language selection
30%
10:40:05
Scheduling
Load shedding
Reduced mode
Water Law
Auto change over
Glycolconcentr.
Communications
Language selection
03.02.2016
1/9Commissioning
Access
Services
Commissioning
Status
1/4Main Menu
1000
50
Reduced
Heating
Low load
None
1/4
Low load
NC
Ecternal switch
On/Off input
1/2
Remote control configuration
20dKdT ret./sup. temp
Remote control
Circuit control
Supply pump
Source Fan
1/5Configuration
correct
Save / load
Operation hours
Deice
Outputs manual test
Configuration
Flow switch
1/6Service
Access
Services
Commissioning
Status
1/4Main Menu
19SysAqua
3.4. LOAD REDUCTION
The Load reduction mode can occasionally be used to limit the electric consumption of the SysAqua to
prevent the energy consumption limits of an installation from being crossed.
Electric consumption is limited by limiting the thermodynamic capacity of SysAqua by means of a modiable
parameter in the Installation menu.
3.4.1. CONFIGURATION
The maximum percentage of reduced load
capacity can be congured by the user
interface in the "Installation" menu via the
"Load reduction" screen.
3.4.2. ACTIVATION
The Load reduction mode can be triggered in the following ways:
² By the external contact: For this, the external contact must be congured in "Load reduction" mode.
This can be congured in the "Maintenance" menu via the "Conguration" screen (Refer to the §
CONFIGURATION, page 12). A closed contact on this input corresponds to the
Load reduction mode. If this contact is congured, it has priority.
² By the user
interface: Go to
the user menu
and modify the operating mode on the relevant line.
² By the GTC: The selection is made by the remote operating
mode variable (0x0000 in modbus)
If the SysAqua is congured in Load reduction mode by the user interface or the GTC, opening the external
contact will not be considered as a Load reduction mode output. However, in the other operating modes
dened by the user interface or the GTC, the Load reduction mode will be taken into account when the
external contact is closed and deactivated when the contact is open.

SystemAir SysAqua 25 Specifications

General

Brand	SystemAir
Model	SysAqua 25
Category	Heat Pump
Language	English