Tektronix 2235 User Manual

O
PER ATI N G I
N STR U CT I O N S
SA FE TY
R efer to the
"Operators Safety Summary"
at the front of
this manual for
p owe r source, grounding, and other
safety
consi d erations p ertaining to the use of
the 2235 . B efore
connecting
the instrument to α p ower
source, carefully rea d
t he
following information about line voltage, power
cor d ,
an
d fuse .
L I NE V O L TAG E
T his instrument is
capable of continuous op eration with
input voltages that range
from 90 V to 250 V nominal at
frequencies
from
48
Hz to 440 Hz .
P O WER CO
R D
Α detac hab le t h ree-wi r e p ower cor d
wit h
α
th ree-co n tact
p l u g is
provided with each i nstru
m ent to permit connection
to b
oth t he p ower source an d protective groun
d . The pro-
tective-groun d contact in the plug connects
(through t he
protective-ground con d uctor) to the accessible
metal p arts
of the
instrument . For electrical-shoc
k protection, insert this
plug only
into α p ower-source outlet that has α
properly
groun d ed p rotective-groun d contact
.
PREP A R ATIO N F O
R
U
S E
P lug

L ine R e f erence Optio n
Configuration U sage
Voltage
Stan d ar ds N um b er
N ort h
ANSI C73 .11
American

120V

ΝΕΜΑ 5-15- Ρ

Stan d ar d
120 Α /

Ι

Ι
I E C 83
Universal
E uro
240 V
/
10-16 Α
UK
240V/
13 Α
N ort h
American
240 V /
15 Α
terclockwise
to
r elease it .
240 V
240V
Section 2-2235 Ser vice
C EE (7},II,I V . V II
I E C
133
Θ 5 1363
I EC 83
Α 1
Α 2
Austra ι ian
240 Α /

240
ν

AS C112

Α 3
10 Α
ANSI
ς 73 .2 ρ
240 V

ΝΕΜΑ 6-15- Ρ

Α 4
I
E C 83
Switzerlan d
220 Υ / 2201 SEV
Α 5
6Α
Abb reviations :
ANSI - American N atio n al Stan d ar ds
Institute
Α 5 - Stan d ar d s Association of Australia
Β5 - B ritis h Stan d ar ds Institution
ςΕΕ - International Commission on R ules for t he
Approval
of E lectrical Eq ui p ment
I E C - Inter n ational
El ectrotec h nical Commission
ΝΕΜΑ - National Electrical Manufacturer's Association
S EV - Sc h weizevisc h er E ι ek trotec h isc h er V erei ο

2931-21
Figure 2-1 . V oltage, po w er
cord,
an
d fuse d ata .
Instruments are shippe d with t he require
d power cord as
or d ere d b y the customer . Available
power-cord information
is presente
d in F igure 2-1, and p
art numbers are liste d on

1 . Unplug the power cord f rom
t
he
power-input source (it
the "Accessories" page at the back of
this manual- Contact

applicable) .
your Tektronix representative or local
Tektronix Field Office
for a d ditional power-cord
information .
2 . Press
in and slightly rotate the
fuse-hol d er cap coun-
L I NEFU S E
3
.
Pull the cap (with t he attached
fuse insi d e) out of the
The instrument
fuse hol d er is located on the rear panel

fuse holder .
(see Figure 2-2) an
d contains the line fuse .
The following
p roce d ure can
be used to verify that the p roper fuse is
in
stalle d
or to install α replacement fuse .

4 . V erify proper fuse value (see
F igure 2-1) .

Tektronix 2235 Specifications

General

Brand	Tektronix
Model	2235
Category	Test Equipment
Language	English