Tektronix AWG7082C User Manual

Troubleshooting
Table 4-7: Calibration error codes (cont.)
Error code Error log message
Possible defect
on board Note
260000101
The difference of ch1_ram_address_timing_1 and
ch2_ram_address_timing_1 is larger than 96.(@10GHz)
AWG12G AWG12G: U400, U500, U510
260000103
The difference of ch1_ram_address_timing_2 and
ch2_ram_address_timing_2 is larger than 96.(@8GHz)
AWG12G AWG12G: U400, U500, U510
260001001
Invalid NG Areas. (ch1_ram_address_timing@10GHz) AWG12G AWG12G: U400xA
260001002
Invalid NG Areas. (ch2_ram_address_timing@10GHz) AWG12G AWG12G: U400xB
260001003
Invalid NG Areas. (ch1_ram_address_timing@8GHz) AWG12G AWG12G: U400xA
260001004
Invalid NG Areas. (ch2_ram_address_timing@8GHz) AWG12G AWG12G: U400xB
260000105
The difference of ch1_ram_data_timing_1 and
ch2_ram_data_timing_1 is larger than 96.(@10G Hz)
AWG12G AWG12G: U400, U500, U510
260000107
The difference of ch1_ram_data_timing_2 and
ch2_ram_data_timing_2 is larger than 96.(@8GHz)
AWG12G AWG12G: U400, U500, U510
260000108
The difference of ch1_ram_data_timing_1 -
ch1_ram_data_timing_2 is larger than 96.
AWG12G AWG12G: U400A, U500A, U510A
260000109
The difference of ch2_ram_data_timing_1 -
ch2_ram_data_timing_2 is larger than 96.
AWG12G AWG12G: U400B, U500B, U510B
260000011
The Cal value is not found.(ch1_pld_timing_1@10GHz) AWG12G AWG12G: U400A
260000012
The Cal value is not found. (ch2_pld_timing_1@10GHz) AWG12G AWG12G: U400B
260000013
The Cal value is not found. (ch1_pld_timing_2@8GHz) AWG12G AWG12G: U400A
260000014
The Cal value is not found. (ch2_pld_timing_2@8GHz) AWG12G AWG12G: U400B
260000015
The Cal value is not found. (ch1_pld_timing_3@10GHz) AWG12G AWG12G: U400A
260000016
The Cal value is not found. (ch2_pld_timing_3@10GHz) AWG12G AWG12G: U400B
260000017
Temperature changed 5 degrees or more. (@PLD
Timing Cal.)
260000111
The difference of ch1_pld_timing_1 and
ch2_pld_timing_1 is larger than 48.(@10G Hz)
AWG12G AWG12G: U400
260000113
The difference of ch1_pld_timing_2 and
ch2_pld_timing_2 is larger than 48.(@8GHz)
AWG12G AWG12G: U400
260000115
The difference of ch1_pld_timing_3 and
ch2_pld_timing_3 is larger than 48.(@10G Hz)
AWG12G AWG12G: U400
260001005
Invalid NG Areas.(ch1_pld_timing@10GHz) AWG12G AWG12G: U400xA
260001006
Invalid NG Areas.(ch2_pld_timing@10GHz) AWG12G AWG12G: U400xB
260001007
Invalid NG Areas.(ch1_pld_timing@8GHz) AWG12G AWG12G: U400xA
260001008
Invalid NG Areas.(ch2_pld_timing@8GHz) AWG12G AWG12G: U400xB
260000021
The C al value is not found.(tek15_ch1_timing_1) AWG12G AWG12G: U 300A
260000022
The C al value is not found.(tek15_ch2_timing_1) AWG12G AWG12G: U 300B
260000023
The C al value is not found.(tek15_ch1_timing_2) AWG12G AWG12G: U 300A
260000024
The C al value is not found.(tek15_ch2_timing_2) AWG12G AWG12G: U 300B
AWG7000B and AWG7000C Series Service Manual 4–67

Tektronix AWG7082C Specifications

General

Brand	Tektronix
Model	AWG7082C
Category	Portable Generator
Language	English