To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if my Xerox Phaser 6120 power is not on?
First, ensure the power cord is correctly plugged into the outlet. If it is, try plugging another electrical appliance into the same outlet to see if it works. Also, check that the power switch is in the on (I) position. If the issue persists, verify that the printer is connected to a power source matching the printer's specifications.
How to fix Xerox Phaser 6120 when media is misfeeding?
First, remove the misfed media and reposition the media properly in the tray. Ensure that you are not exceeding the maximum number of sheets allowed in the tray. Adjust the media guides to match the media size. If you are using warped or wrinkled media, smooth it out or replace it. Also, if the media is moist, replace it with dry media. Special media must be loaded in Tray 1 only. Ensure that transparencies or label sheets are loaded according to the manufacturer's instructions and envelopes are loaded with the flaps facing down.
What to do if my Xerox Phaser 6120 is printing blank pages?
Check the toner cartridges to make sure they are not empty or defective. If a cartridge is empty, the image will not print. Also, verify that the media type set in the driver matches the media loaded in the printer.
What to do if the paper jam message stays on Xerox Printer?
Open and close the top cover of the printer again to reset it. Also, recheck the media path to ensure all jammed paper has been removed.
Why does my Xerox Phaser 6120 keep resetting or turning off?
Ensure the power cord is correctly plugged into the outlet. If the problem persists, contact your local Xerox service representative with the error information, as a system error may have occurred.
What to do if several sheets go through my Xerox Printer together?
Make sure the front edges of the media are even. Remove the media, even up the front edges, and then reload it. If the media is moist, replace it with new, dry media. Also, avoid fanning transparencies, as this can cause static electricity.
What to do if my Xerox Phaser 6120 Printer duplex unit jams?
Use Xerox-approved media. Recheck the media path inside the duplex unit and remove all jammed paper.
Why does my Xerox Printer take too much time to print?
If the printer is set to a slow printing mode for special media, it will take longer. Ensure the media type is set properly in the driver when using regular paper. Printing may also take longer if the printer is in power saving mode. Complex jobs also require more time. Insufficient printer memory and unapproved toner cartridges can also cause delays; add more memory or install an approved toner cartridge.
What to do if my Xerox Printer media is wrinkled?
Replace the moist media with new, dry media if humidity or water spillage is the cause. Check the media feed roller or fuser unit for damage. Use Xerox-approved media. Before printing envelopes, place both green fuser separator levers in the envelope position.
What to do if I hear unusual noises from my Xerox Printer?
Ensure the printer is on a flat, hard, level surface. Remove the tray and reinsert it completely. If there is a foreign object stuck inside, turn off the printer and remove it. If you cannot remove it, contact Technical Support.
General| Color | Yes |
|---|---|
| Print technology | Laser |
| Time to first page (black, normal) | 13 s |
| Time to first page (color, normal) | 22 s |
| Print speed (black, normal quality, A4/US Letter) | 20 ppm |
| Print speed (color, normal quality, A4/US Letter) | 5 ppm |
| Internal memory | 128 MB |
| Processor model | 300 MHz, 32 bit RISC |
| Maximum print size | 210 x 297 mm |
| Maximum ISO A-series paper size | A4 |
| I/O ports | USB |
| Power requirements | 200 – 240 VAC / 100 – 127 VAC 50/60 Hz |
| Networking features | Ethernet/Fast-Ethernet |
| Non-operating relative humidity (non-condensing) | 10 - 85 % |
| Total input capacity | 200 sheets |
| Maximum input capacity | 500 sheets |
| Printer fonts | PostScript |
| Maximum duty cycle | 35000 pages per month |
| Number of PostScript fonts | 139 |
| Power consumption (printing) | 380 W |
| Storage temperature (T-T) | -20 - 40 °C |
| Operating temperature (T-T) | 10 - 32 °C |
| Operating relative humidity (H-H) | 10 - 80 % |
Weight and Dimensions| Dimensions (WxDxH) | 442 x 395 x 341 mm |
|---|
Explains how to connect the printer to a TCP/IP network environment.
Guides on configuring printer driver settings for Windows OS.
Settings for managing media loaded in the printer trays.
Settings for controlling print quality and toner management.
Information about replacing printer consumables, specifically toner.
Detailed step-by-step instructions for replacing toner cartridges.
Procedures for replacing routine maintenance components.
General precautions and guidelines for cleaning the printer.
General procedures and warnings for clearing paper jams.
Troubleshooting table for common paper jam symptoms, causes, and solutions.
Troubleshooting table for various printer issues like power, control panel, and page printing.
Troubleshooting table for print quality issues like blank pages, density, and smudges.
Explains status, warning, operator call, and service messages.
Crucial safety instructions for preventing electrostatic damage to printer components.
Comprehensive safety guidelines for operating and maintaining the printer.
