TIGHTENING TORQUES
EA$20350
CHASSIS TIGHTENING TORQUES
It
em
Thread
Q'
ty
Tight
e
ning
torque
Remarks
size
Engine mounting
bo
lt (front upp
er
M10
4
45
Nm
(4.5 m·kgf, 33 ft·lbf)
and
fr
ont lower)
Engine mounting nut (rear upper) M10 1 45
Nm
(4.5 m·kgf, 33 ft·lbf)
Engine mounting nut (rear lower) M10 1 45
Nm
(4.5 m·kgf, 33 ft·lbf)
Engine mounting adjust bolt
M1S 1 7 Nm (0.7 m·kgf,
5.1
ft·lbf)
(front)
Engine mounting adjust bolt
M16
2
7 Nm (0.7 m·kgf,
5.1
ft·lbf)
(rear)
Main frame and rear frame nut M10 4 50 Nm (5.0 m·kgf, 36 ft·lbf)
-<lt
Pivot shaft n
ut
M14 1 1
10
Nm
(11
m·kgf,
SO
ft·lbf)
Relay arm and frame nut M10 1
61
Nm
(6.1
m·kgf, 44 ft·lbf)
Relay arm and connecting arm
M10 1 55
Nm
(5.5 m·kgf, 40 ft·lbf)
n
ut
Connecting arm and swingarm
M10 1 55
Nm
(5.5 m·kgf, 40 ft·lbf)
assembly nut
Rear shock absorber assembly
M10 1 44
Nm
(4.4 m·kgf, 32 ft·lbf)
nut (upper)
Rear shock absorber assembly
M10 1 44
Nm
(4.4 m·kgf, 32 ft·lbf)
nut (lower)
Dr
iv
e chain guard bolt M6
2
7 Nm (0.7 m·kgf,
5.1
ft·lbf)
Rear fender
bo
lt M6 3 7 Nm (0.7 m·kgf,
5.1
ft·
lbf)
Sw
ingarm bracket (left) and
M6 4 7 Nm (0.7 m·kgf,
5.1
ft·lbf)
-<lt
swingarm bolt
Sw
ingarm bracket (right) and
M6
4
7 Nm (0.7 m·kg
f,
5.1
ft·lbf)
-<lt
swingarm
bo
lt
Chain puller adjusting locknut
MS
2
16
Nm
(1.6 m·kgf, 12 ft·lbf)
Upper bracket pinch bolt
MS
2 26
Nm
(2.6 m·kgf, 19 ft·lbf)
Steering stem nut M22 1 1
10
Nm
(11
m·kgf,
SO
ft·lbf)
Upper handlebar holder
bo
lt
MS
4 22
Nm
(2.2 m·kgf, 16 ft·lbf)
Lower ring nut M25 2 See
TIP.
Lower handlebar holder nut M10
2
40
Nm
(4.0 m·kgf, 29 ft·lbf)
Front brake master cylinder
M6 2 1 O
Nm
(1
.0 m·kgf, 7.2 ft·lbf)
holder bolt
Front brake hose uni
on
bolt M10 3 30
Nm
(3.0 m·kgf, 22 ft·lbf)
Lower bracket pinch bolt
MS
4 23
Nm
(2.3 m·kgf, 17 ft-lbf)
Main switch and upper bracket
MS
2
23
Nm
(2.3 m·kgf, 17 ft·lbf)
Gr
ip end M16 2 26
Nm
(2.6 m·kgf, 19 ft·lbf)
2-18
To Next Page
Loading...
Need help?
General
