D-Link DGS-1210-10P User Manual

5 Configuration D-Link Web Smart Switch User Manual
If choosing SNTP for the clock source, then the following parameters will be available:
SNTP First Server: Specify the IP address of the primary SNTP server from which the system time is
retrieved.
SNTP Second Server: Specify the IP address of the secondary SNTP server from which the system time is
retrieved.
SNTP Poll Interval in Seconds (30-99999): Defines the interval (in seconds) at which the SNTP server is
polled for Unicast information. The Poll Interval default is 30 seconds.
Click Apply to implement changes made.
When selecting Local for the clock source, users can select from one of two options:
Manually set current time: Users input the system time manually.
Set time from PC: The system time will be synchronized from the local computer.
Configuration > SNTP Settings > TimeZone Settings
The TimeZone Setting Page is used to configure time zones and Daylight Savings time settings for SNTP.
Figure 68 – Configuration > SNTP Settings > TimeZone Settings
Daylight Saving Time State: Use this drop-down menu to enable or disable the DST Settings.
Daylight Saving Time Offset in Minutes: Use this drop-down menu to specify the amount of time that will
constitute your local DST offset - 30, 60, 90, or 120 minutes.
Time Zone Offset from GMT in +/- HH:MM: Use these drop-down menus to specify your local time zone's
offset from Greenwich Mean Time (GMT.)
DST Annual Settings: Using annual mode will enable DST seasonal time adjustment. Annual mode
requires that the DST beginning and ending date must not be in the same month. For example, specify to
begin DST on March 8 and end DST on November 1.
From: Month: Enter the month DST will start on, each year.
From: Day: Enter the day of the week DST will start on, each year.
From: Time in HH:MM: Enter the time of day DST will start on, each year.
To: Month: Enter the month DST will end on, each year.
To: Day: Enter the date DST will end on, each year.
To: Time in HH:MM: Enter the time of day that DST will end on, each year.
Click Apply to implement changes made.
Configuration > Spanning Tree > STP Global Settings
The Switch implements two versions of the Spanning Tree Protocol, the Rapid Spanning Tree Protocol
(RSTP) as defined by the IEEE 802.1w specification and a version compatible with the IEEE 802.1D STP.
RSTP can operate with legacy equipment implementing IEEE 802.1D, however the advantages of using
RSTP will be lost.
40

D-Link DGS-1210-10P Specifications

General

Number of queues	4
MAC address table	8000 entries
Store-and-forward	Yes
Packet buffer memory	0.5 MB
Maximum data transfer rate	1 Gbit/s
Supported data transfer rates	10/100/1000 Mbps
10G support	No
Networking standards	IEEE 802.2, IEEE 802.3, IEEE 802.3u, IEEE 802.3x
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Networking features	Gigabit Ethernet
Packet transfer speed	14.88
Connectivity technology	Wired
Ethernet interface type	Fast Ethernet, Gigabit Ethernet
DHCP features	DHCP server, DHCP client
Security algorithms	802.1x RADIUS
Switch type	-
Switch layer	L2
Fiber optic connector	SFP
SFP/SFP+ slots quantity	2
Basic switching RJ-45 Ethernet ports quantity	10
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	109.6 W
Safety	cUL, LVD
Certification	FCC, CE, IC, VCCI, C-Tick
Product color	Black
Storage temperature (T-T)	-10 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	10 - 95 %

Weight and Dimensions

Depth	180 mm
Width	330 mm
Height	44 mm
Weight	1840 g