Name: Danfoss ECL COMFORT
Brand: Danfoss
Rating: 5 (1 reviews)

To Next Page

To Previous Page

List of Components2
Controller Mode2
Table of Contents3
Before You Start5
- Installation6
- System Settings6
Identifying the System Type6
- Mounting on a Wall12
- Mounting on a DIN Rail12
- Mounting in a Panel12
Mounting the ECL Comfort Controller12
Electrical Connections - 230 V A.C.14
Electrical Connections 24 V A.C15
Electrical Connections - 24 V A.C.16
Connecting and Placing the Temperature Sensors18
- Connecting the Room Panel / Remote Control20
- Override20
Inserting the ECL Card22
- Understanding the ECL Card23
- Basic Set-Up24
Adjusting the ECL Card Settings24
Setting the Time and Date - Line a25
Monitoring Temperatures and System Units - Line B26
Manual Control - Line B27
- The Motorized Actuator27
- The Thermo Actuator27
- Storage Temperature (Circuit II) - Line C28
- Setting the Heat Curve (Circuit I)28
- Heating Cut-Out - Line 130
- Flow Temperature Limits - Line 231
- Room Temperature Influence - Line 332
- Max. Room Temperature Limitation32
- Reference Room Temperature Control33
- Control Parameters - Lines 4-734
- Cut-In and Cut-Out Temperature at DHW Charging - Lines 1-2, Circuit II36
- Controls and Overviews38
Check List38
- ECL Card Settings (Circuit I)40
- ECL Card Settings (Circuit II)41
- Time and Date41
Service Parameters42
Extended Service46
Adjusting the Service Parameters46
- Choice of Room Panel / Remote Control47
- Setback Temperature Dependent on Outdoor Temperature47
- Boost48
- Reference Ramping48
- Optimizing Time Constant49
- Adaptive Function of Room Temperature49
- Inﬂuence on Desired Flow Temperature50
- Optimization Based on Room / Outdoor Temperature51
- Total Stop51
- Pump Exercise52
- Valve Exercise52
- Gear Motor / Thermo Actuator52
- Return Temperature Limitation53
- Return Temperature Inﬂuence - Max. Limitation55
- Return Temperature Inﬂuence - Min. Limitation56
- Time Constant for Return Temperature Limitation57
- DHW Pump Post-Run (P2)57
- DHW Charging Pump Post-Run (P4)57
- Parallel Operation of DHW and Heating Circuits58
- Max. DHW Charging Time59
- DHW Charging Deactivation Time59
- Closed Valve / Normal Operation59
- Compensation of Heat Loss in Circulation Circuit60
- Activation / Deactivation of DHW Circulation Pump During DHW Charging60
- Internal Relationship between Circuits I and II61
- Anti-Bacteria Function Period61
- Desired Temperature for Anti-Bacteria Function61
- Pump P2 in DHW Circuit, Primary Side62
- Assignment (Number) of Heat Meters63
- Function of Temperature Sensor S564
- Override Input Selection65
- Acceptable Temperature Deviation below Desired Flow Temperature66
- Acceptable Temperature Deviation above the Desired Flow Temperature67
- Time Interval Alarm before Activation of Alarm Function68
- Motor Protection69
- LON Reset69
- Daylight Saving Time Changeover69
- Master / Slave Address70
Copying with the ECL Card72
- Copy Personal Settings to Additional Controller in Identical Systems73
- Deﬁnitions74
- Factory Settings74
- Hot Points76
- Advantages of the ECL Card78
- Save Your Personal Settings to the ECL Card78
- Restore ECL Card Data79
- Set Your Personal Schedule80
- Monitor the Current Schedules80
- Change the Schedules80
- Change the Schedule for Circuit II80
- Add an Extra Comfort Period81
- Remove a Comfort Period81
- Cancel Changes in Your Personal Settings81
Select Circuit Mode82
Set Your Room and DHW Charging Temperature83
- Choose Your Favorite Display (Circuit I)84
- Room Temperature - Display a84
- System Information - Display B84
- Today's Schedule - Display C84
- Choose Your Favorite Display (Circuit II)85
- DHW Temperature - Display a85
- Schedule, DHW Circulation Pump (P3)86
- Operating the ECL Comfort Controller87
Set Your Personal Schedule88
Advantages of the ECL Card88
Hot Points88
Deﬁnitions88

Brand	Danfoss
Model	ECL COMFORT
Category	Control Panel
Language	English

Danfoss ECL COMFORT User Manual

Table of Contents

Questions and Answers:

Danfoss ECL COMFORT Specifications

Related product manuals