Datalogic QuickScan QD2590 User Manual

SETUP
4 QUICKSCAN™ QD2590
CONNECT HOST INTERFACE
The reader kit you ordered to match your interface should provide a compatible cable
for your installation. If this is not so, contact "
Technical Support" on page xii.
The reader can communicate using the interfaces illustrated below.
For corded versions, connect the reader cable by inserting the cable into the handle as
shown in the following Figure.
To remove the interface cable from the reader, first locate the hole on the back of the
handle. Next, take a paper clip and modify it as shown in the figure below. Insert the
end of the paper clip into the hole and press it to push on the clip that holds the connec-
tor. As you apply pressure, pull out the cable.
When reinserting the cable, make sure the connector clip is on the same side as the
reader release hole. Insert the cable, it should click when it is fully inserted.
Figure 2. Cable Connection/Disconnection at the Reader
RS-232 Serial Connection
Turn off power to the terminal/PC and connect the reader to the terminal/PC serial port
via the RS-232 cable as shown in Figure 3. If the terminal will not support POT (Power
Off the Terminal) to supply reader power, use the approved power supply (AC Adapter).
Plug the AC Adapter barrel connector into the socket on the RS-232 cable connector and
the AC Adapter plug into a standard power outlet.
RS-232: The reader can communicate with a standard or Wincor-Nixdorf (W-N) RS-232
host.
RS-232 OPOS: This interface is used for OPOS/UPOS/JavaPOS systems.
Keyboard Wedge Connection
The Keyboard Wedge cable has a ‘Y’ connection from the reader. Connect the female to
the male end from the keyboard and the remaining end at the keyboard port at the ter-
minal/PC.
Keyboard Wedge (KBW): When connected using this interface, the host interprets
scanned data as keystrokes and supports several international keyboards (for the Win-
dows® environment). See "
Setting Country Mode" on page 36 for a full listing.
NOTE: We recommend the use of a perfectly straight new paper clip to
make the operation easier (see the figure below).
Paper Clip
Cable Connector

Datalogic QuickScan QD2590 Specifications

General

Type	Handheld bar code reader
Sensor type	-
Scanner type	1D/2D
Scanner resolution	0.17 mm
Tilt reading angle	0 - 360 °
Pitch reading angle	0 - 65 °
Light levels (direct sunlight)	0 - 100000 lx
Linear (1D) barcodes supported	CPC Binary, Codabar, Codabar 125, Code 11, Code 128, Code 128A, Code 128B, Code 128C, Code 25 (IR 2 of 5), Code 25 (non-IR 2 of 5), Code 3 of 9, Code 32, Code 39, Code 93, DUN 14, DataBar14, Discrete 2 of 5, EAN 128, EAN 2, EAN 5, EAN-13, EAN-8, Facing Identification Mark, GS1 DataBar, GS1 DataBar Expanded, GS1 DataBar Omnidirectional, GS1 Databar Limited, GS1-128 (UCC/EAN-128), HIBC, IATA, ISBN, ISSN, ITF-14, ITF-6, Industrial 2 of 5, Intelligent Mail, Interleaved 2 of 5, JAN, Latent image, MSI, Matrix 2 of 5, PDF417, PLANET, POSTNET, Pharmacode, Plessey, PostBar, RM4SCC / KIX, S-Code, Telepen, Trioptic, U.P.C., UPC-A, UPC-E
Optical sensor resolution (W x H)	1280 x 800 pixels
2D (matrix & stacked) barcodes supported	Aztec Code, Data Matrix, Dot Code A, MaxiCode, Micro QR Code, QR Code
Cable length	2 m
Standard interfaces	USB
Connectivity technology	Wired
Product color	Black
Image formats supported	BMP, JPEG, TIFF
International Protection (IP) code	IP52
Input voltage	5 V
Power consumption	450 mA
Cables included	USB Type-C
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Operating relative humidity (H-H)	0 - 95 %
Sustainability certificates	RoHS
Material	Polyvinyl chloride (PVC)
Connector 1	USB C
Product type	USB cable
Connector gender	Male/Male
Brand compatibility	Datalogic
Connector 1 form factor	Straight
Harmonized System (HS) code	84733020

Weight and Dimensions

Depth	126 mm
Width	148 mm
Height	68 mm
Weight	145 g