Dell POWEREDGE R710 User Manual

Installing System Components 81
All drives are installed at the front of the system and connect to the system
board through the SAS backplane. Hard drives are supplied in special hot-
swappable hard-drive carriers that fit in the hard-drive bays.
CAUTION: Before attempting to remove or install a drive while the system is
running, see the documentation for the storage controller card to ensure that the
host adapter is configured correctly to support hot-swap drive removal and
insertion.
CAUTION: Do not turn off or reboot your system while the drive is being formatted.
Doing so can cause a drive failure.
NOTE: Use only drives that have been tested and approved for use with the SAS
backplane board.
When you format a hard drive, allow enough time for the formatting to be
completed. Be aware that high-capacity hard drives can take a number of
hours to format.
Mixed SAS/SATA Hard-Drive Configurations
Mixed hard-drive configurations of SAS and SATA drives are allowed. In this
configuration, two SAS drives must be installed in hard-drive slots 0 and 1
only. The remaining slots can have SATA drives installed.
Mixed 2.5-inch and 3.5-inch configurations of SAS and SATA drives are also
supported in the 3.5-inch–bay chassis only. In this configuration, two 10,000-
RPM 2.5-inch SAS drives installed in 3.5-inch adapters must be used in hard-
drive slots 0 and 1 only (see "Front-Panel Features and Indicators"). The
remaining hard drives must be 3.5 inches in size and must be either all SAS or
all SATA drives.
Removing a Hard-Drive Blank
CAUTION: To maintain proper system cooling, all empty hard-drive bays must
have drive blanks installed.
1 Remove the front bezel. See " Removing the Front Bezel ."
2 Grasp the front of the hard-drive blank, press the release lever on the
right side, and
slide the blank out until it is free of the drive bay . See
Figure 3-4 .

Dell POWEREDGE R710 Specifications

General

Tcase	76 °C
Bus type	QPI
Stepping	D0
FSB Parity	No
Processor code	SLBF7
Processor cache	8 MB
Processor cores	4
Processor model	E5530
System bus rate	5.86 GT/s
Processor series	Intel Xeon 5500 Series
Processor socket	Socket B (LGA 1366)
Processor threads	8
Processor codename	Nehalem EP
Motherboard chipset	Intel® 5520
Number of QPI links	2
Processing Die size	263 mm²
Processor frequency	2.4 GHz
Processor cache type	Smart Cache
Processor lithography	45 nm
Processor system type	DP
Processor manufacturer	Intel
Processor package size	42.5 x 45 mm
Processor front side bus	- MHz
Processor boost frequency	2.66 GHz
Processor operating modes	64-bit
ECC supported by processor	Yes
Thermal Design Power (TDP)	80 W
Number of processors installed	1
CPU multiplier (bus/core ratio)	18
Memory types supported by processor	DDR3-SDRAM
Number of Processing Die Transistors	731 M
Memory channels supported by processor	Triple
Memory clock speeds supported by processor	800, 1066 MHz
Memory bandwidth supported by processor (max)	25.6 GB/s
Maximum internal memory supported by processor	144 GB
HDD size	3.5 \
HDD capacity	146 GB
HDD interface	Serial Attached SCSI (SAS)
Optical drive type	DVD-ROM
Total storage capacity	292 GB
Maximum storage capacity	6 TB
Internal memory	12 GB
Memory clock speed	1066 MHz
Memory layout (slots x size)	6 x 2 GB
Graphics card	G200
Dimensions (WxDxH)	443.1 x 680.7 x 86.4 mm
Non-operating relative humidity (non-condensing)	5 - 95 %
PS/2 ports quantity	0
USB 2.0 ports quantity	5
Power supply	570 W
Power requirements	90 - 264V
Compatible operating systems	Windows Server, Standart Business Server, Novell SUSE Linux, Red Hat Linux Enterprise
Chassis type	Rack (2U)
Storage temperature (T-T)	-40 - 65 °C
Operating temperature (T-T)	10 - 35 °C
Operating relative humidity (H-H)	20 - 80 %
Networking features	Gigabit Ethernet
Processor ARK ID	37103
Intel® Turbo Boost Technology	1.0

Weight and Dimensions

Depth	680.7 mm
Width	443.1 mm
Height	86.4 mm
Weight	26100 g