Denon AVR-3311 User Manual

10
ENGLISH
Parameter Check
This function enables you to check the measurement results and
equalizer characteristics after Audyssey Auto Setup.
1
8VH ui WR VHOHFW ³3DUDPHWHU &KHFN´ DQG WKHQ
SUHVV
ENTERRUp
2
8VHuiWRVHOHFWWKHLWHP\RXZDQWWRFKHFNWKHQ
SUHVV
ENTERRUp
Measurement results for each speaker are displayed.
6SHDNHU&RQILJ&KHFN
'LVWDQFH&KHFN
&KDQQHO/HYHO&KHFN
&URVVRYHU&KHFN
(4&KHFN
5HVWRUH
$8726(783
3$5$0(7(5&+(&.
6KRZVSHDNHUFRQILJXUDWLRQUHVXOW
Speaker Config. Check
Distance Check
Channel Level Check
Crossover Check
EQ Check
Check the speaker configuration.
Check the distance.
Check the channel level.
Check the crossover frequency.
Check the equalizer.
• If “EQ Check” is selected in step 2, press
ui to select equalizing
curve (“Audyssey” or “Audyssey Flat”) to be checked.
Use
o p to switch the display between the different speakers.
3
3UHVVRETURN
The confirmation screen reappears. Repeat steps 2.
Retrieving Audyssey Auto Setup settings
If you set “Restore” to “Yes”, you can return to Audyssey Auto Setup
measurement result (value calculated at the start by MultEQ
®
XT)
even when you have changed each setting manually.
Error messages
An error message is displayed if Audyssey
®
Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples Error details Measures
&DXWLRQ
1RPLFURSKRQHRU6SHDNHU
5HWU\
&KHFNFDXVHRISUREOHP
$8726(783
$8'<66(<$8726(783
5(7851 &DQFHO
0XOW(4;7
• The connected setup microphone is broken,
or adevice other than the supplied setup
microphone is connected.
• Not all speakers could be detected.
• The front L speaker was not properly
detected.
• Connect the included setup microphone to
the SETUP MIC jack of this unit.
• Check the speaker connections.
&DXWLRQ
$PELHQWQRLVHLVWRRKLJK
RU/HYHOLVWRRORZ
5HWU\
&KHFNFDXVHRISUREOHP
$8726(783
$8'<66(<$8726(783
5(7851 &DQFHO
0XOW(4;7
• There is too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• Either turn off any device generating noise
or move it away.
• Perform again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are facing.
• Adjust the subwoofer’s volume.
&DX LRQ
&KHFNFDXVHRISUREOHP
5HWU\
)URQW5 1RQH
$8726(783
$8'<66(<$8726(783
5(7851 &DQFHO
0XOW(4;7
• The displayed speaker could not be detected. • Check the connections of the displayed
speaker.
&DX LRQ
&KHFNFDXVHRISUREOHP
5HWU\
6NLS
)URQW/ 3KDVH
$8726(783
$8'<66(<$8726(783
5(7851 &DQFHO
0XOW(4;7
• The displayed is connected with the
polarities reversed.
• Check the polarities of the displayed
speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press
ui to select “Skip”, then
press
ENTER.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu

Denon AVR-3311 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/192kHz
Signal-to-Noise Ratio (SNR)	102 dB
Total Harmonic Distortion (THD)	0.05 %
Power output per channel (1KHz@6 Ohm)	165 W
Power output per channel (20-20KHz@8 Ohm)	125 W
Optical drive included	No
Display	LED
Equalizer	Yes
HDMI version	1.4a
Product color	Silver
Audio decoders	DTS 96/24, DTS-ES (Discrete 6.1), DTS-HD, DTS-HD Master Audio, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD
Volume control	Rotary
Multi-Zone quantity	4
Apple docking compatibility	iPod Classic 4, iPod Classic 5, iPod Mini 1, iPod Mini 2, iPod Nano 1, iPod Nano 2
Supported video modes	1080p
HDMI in	6
Audio (L/R) in	9
Composite video in	5
USB ports quantity	1
S-Video inputs quantity	2
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
AM band range	522 - 1611 kHz
FM band range	57.5 - 108 MHz
Composite video out	3
Headphone connectivity	3.5 mm/6.35 mm
Digital audio coaxial out	0
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	670 W

Weight and Dimensions

Depth	381 mm
Width	434 mm
Height	171 mm
Weight	12200 g