Epson PowerLite EB-L210SF User Manual

176
• If you enter an incorrect password three times in succession, you see a message telling you that
the projector is locked. After the message is displayed for 5 minutes, the projector enters standby
mode. Unplug the projector, plug in the power cord, and turn on the projector. You see a prompt to
enter the password.
• If you continue to enter an incorrect password many times in succession, the projector displays a
request code and a message to contact Epson Support. Do not attempt to enter the password
again. When you contact Epson Support, provide the displayed request code and proof of
ownership for assistance in unlocking the projector.
Parent topic: Password Security Types
Saving a User's Logo Image to Display
You can transfer an image to the projector and then display it whenever the projector turns on. You can
also display the image when the projector is not receiving an input signal or when you temporarily stop
projection. This transferred image is called the User's Logo screen.
The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in
identifying the projector's owner to help deter theft. You can prevent changes to the User's Logo by
setting up password protection for it.
Note: You cannot save an image that is protected by HDCP as a User's Logo. You cannot display a
user's logo when Content Playback is set to On. If you turned on password protection for the User's
Logo, turn it off before performing these steps.
Note: When you copy the menu settings from one projector to another using the batch setup feature, the
user logo is also copied. Do not include any information in the user logo that you do not want to share
between multiple projectors.
1. Display the image you want to project as the User's Logo.

Epson PowerLite EB-L210SF Specifications

General

DVI port	No
Microphone in	Yes
Audio (L/R) in	1
Composite video in	-
Serial interface type	RS-232C
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Matrix size	0.62 \
Heat dissipation	884 BTU/h
Number of colors	1.07 billion colors
White light output	4000 ANSI lumens
Native aspect ratio	16:9
Projection technology	3LCD
Contrast ratio (dynamic)	2500000:1
Screen size compatibility	55 - 125 \
Keystone correction, horizontal	-15 - 15 °
Video color modes	Blackboard, Cinema, DICOM simulation mode, Dynamic, Multi-projection, Presentation, sRGB
Supported video modes	1080p
Wi-Fi standards	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Noise level	37 dB
Country of origin	Philippines
Noise level (economic mode)	27 dB
Light source type	Laser
Service life of light source	20000 h
Service life of light source (economic mode)	30000 h
Color depth	10 bit
Focus	Manual
Throw ratio	0.45 - 0.61:1
Placement	Ceiling, Desktop, Wall
Product type	Short throw projector
Product color	White
Market positioning	Portable
Cable lock slot type	Kensington
Supported network protocols	HTTPS, IPv4, IPv6, SNMP, ESC/VP.net, PJLink
Cord length	1.8 m
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50/60 Hz
Power consumption (standby)	0.5 W
Power consumption (typical)	201 W
Power consumption (economy mode)	191 W
RMS rated power	16 W
Cables included	AC, HDMI
Bundled software	EasyMP Multi PC Projection, Epson Projector Content Manager, Epson Projector Management
Storage temperature (T-T)	-10 - 60 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	337 mm
Width	325 mm
Height	90 mm
Weight	4600 g