EasyManuals Logo

Ford Escape 2013 User Manual

Ford Escape 2013
892 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #223 background imageLoading...
Page #223 background image
WARNINGS
Do not add coolant further than the
MAX mark.
Note: Do not use stop leak pellets, cooling
system sealants, or additives as they can
cause damage to the engine cooling or
heating systems. This damage would not
be covered under your vehicles warranty.
Note: During normal vehicle operation, the
engine coolant may change color from
orange to pink or light red. As long as the
engine coolant is clear and uncontaminated,
this color change does not indicate the
engine coolant has degraded nor does it
require the engine coolant to be drained, the
system to be flushed, or the engine coolant
to be replaced.
Do not mix different colors or types of
coolant in your vehicle. Make sure the
correct coolant is used. Mixing of
engine coolants may harm your
engines cooling system. The use of an
improper coolant may harm engine and
cooling system components and may
void the warranty. Use prediluted
engine coolant meeting the Ford
specification. See Capacities and
Specifications (page 267).
In case of emergency, a large amount
of water without engine coolant may
be added in order to reach a vehicle
service location. In this instance, the
cooling system must be drained,
chemically cleaned with Motorcraft®
Premium Cooling System Flush, and
refilled with prediluted engine coolant
as soon as possible. Water alone
(without engine coolant) can cause
engine damage from corrosion,
overheating or freezing.
Do not use alcohol, methanol, brine or
any engine coolants mixed with alcohol
or methanol antifreeze (coolant).
Alcohol and other liquids can cause
engine damage from overheating or
freezing.
Do not add extra inhibitors or additives
to the coolant. These can be harmful
and compromise the corrosion
protection of the engine coolant.
Unscrew the cap slowly. Any pressure will
escape as you unscrew the cap.
Add prediluted engine coolant meeting the
Ford specification. See Capacities and
Specifications (page 267).
Whenever coolant has been added, the
coolant level in the coolant reservoir
should be checked the next few times you
drive the vehicle. If necessary, add enough
prediluted engine coolant to bring the
coolant level to the proper level.
Recycled Engine Coolant
Ford Motor Company does not recommend
the use of recycled engine coolant since a
Ford-approved recycling process is not yet
available.
Always dispose of used automotive fluids
in a responsible manner. Follow your
communitys regulations and standards
for recycling and disposing of automotive
fluids.
223
Maintenance

Table of Contents

Other manuals for Ford Escape 2013

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ford Escape 2013 and is the answer not in the manual?

Ford Escape 2013 Specifications

Curb Weight IconCurb Weight
curb weight 1.6L FWD3502 lbs
curb weight 1.6L 4WD3645 lbs
curb weight 2.0L FWD3592 lbs
curb weight 2.0L 4WD3732 lbs
curb weight 2.5L FWD3515 lbs
Seating and Interior IconSeating and Interior
seating capacity5
head room front39.9 inches
head room rear39.0 inches
shoulder room front56.0 inches
shoulder room rear55.3 inches
hip room front54.8 inches
hip room rear52.4 inches
leg room front43.1 inches
leg room rear36.8 inches
Passenger and Cargo Volume IconPassenger and Cargo Volume
passenger volume98.1 cu. ft.
cargo volume behind 1st row67.8 cu. ft.
cargo volume behind 2nd row34.3 cu. ft.
total interior volume132.4 cu. ft.
Fuel IconFuel
fuel tank capacity15.0 gallons
fuel requirement87 octane
fuel economy 2.5L FWD22/31 mpg (city/hwy)
fuel economy 1.6L FWD23/33 mpg (city/hwy)
fuel economy 1.6L 4WD22/30 mpg (city/hwy)
fuel economy 2.0L FWD22/30 mpg (city/hwy)
fuel economy 2.0L 4WD21/28 mpg (city/hwy)
Engine Specifications IconEngine Specifications
engine type 1.6LEcoBoost I-4
engine type 2.0LEcoBoost I-4
engine type 2.5Li-VCT I-4
displacement 1.6L97.6 cu. in.
displacement 2.0L122 cu. in.
displacement 2.5L152 cu. in.
horsepower 1.6L178 @ 5700 rpm
horsepower 2.0L240 @ 5500 rpm
horsepower 2.5L168 @ 6000 rpm
torque 1.6L184 lb.-ft. @ 2500 rpm
torque 2.0L270 lb.-ft. @ 3000 rpm
torque 2.5L170 lb.-ft. @ 4500 rpm
compression ratio 1.6L10.0:1
compression ratio 2.0L9.3:1
compression ratio 2.5L9.7:1
bore and stroke 1.6L3.11 x 3.20 inches
bore and stroke 2.0L3.44 x 3.27 inches
bore and stroke 2.5L3.50 x 3.94 inches
fuel system 1.6LDirect Injection
fuel system 2.0LDirect Injection
fuel system 2.5LSequential Multiport Injection
Weight and Dimensions IconWeight and Dimensions
wheelbase105.9 inches
length178.1 inches
height66.3 inches
width with mirrors81.8 inches
width without mirrors72.4 inches
track front61.5 inches
track rear61.6 inches
ground clearance7.9 inches

Related product manuals