EasyManuals Logo

Ford Escape 2013 User Manual

Ford Escape 2013
892 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #240 background imageLoading...
Page #240 background image
For routine cleaning, wipe the surface
with a soft, damp cloth. For more
thorough cleaning, wipe the surface
with a mild soap and water solution. In
Canada, use Motorcraft® Vinyl Cleaner.
Dry the area with a soft cloth.
If the leather cannot be completely
cleaned using a mild soap and water
solution, the leather may be cleaned
using a commercially available leather
cleaning product designed for
automotive interiors.
To check for compatibility, first test any
cleaner or stain remover on an
inconspicuous part of the leather.
Do not use household cleaning
products, alcohol solutions, solvents
or cleaners intended for rubber, vinyl
and plastics, or oil/petroleum-based
leather conditioners. These products
may cause premature wearing or
damage to the leather.
CLEANING THE ALLOY
WHEELS (IF EQUIPPED)
Note: Do not use chrome cleaner, metal
cleaner or polish on wheels and wheel
covers.
Aluminum wheels and wheel covers are
coated with a clear coat paint finish. In
order to maintain their shine:
Clean weekly with Motorcraft® Wheel
and Tire Cleaner. Heavy dirt and brake
dust accumulation may require
agitation with a sponge. Rinse
thoroughly with a strong stream of
water.
Never apply any cleaning chemical to
hot or warm wheel rims or covers.
Some automatic car washes may
cause damage to the finish on your
wheel rims or covers.
Industrial-strength (heavy-duty)
cleaners, or cleaning chemicals, in
combination with brush agitation to
remove brake dust and dirt, could wear
away the clear coat finish over time.
Do not use hydrofluoric acid-based or
high caustic-based wheel cleaners,
steel wool, fuels or strong household
detergent.
To remove tar and grease, use
Motorcraft® Bug and Tar Remover.
VEHICLE STORAGE
If you plan on storing your vehicle for an
extended period of time (30 days or more),
read the following maintenance
recommendations to make sure your
vehicle stays in good operating condition.
All motor vehicles and their components
were engineered and tested for reliable,
regular driving. Long term storage under
various conditions may lead to component
degradation or failure unless specific
precautions are taken to preserve the
components.
General
Store all vehicles in a dry, ventilated
place.
Protect from sunlight, if possible.
If vehicles are stored outside, they
require regular maintenance to protect
against rust and damage.
240
Vehicle Care

Table of Contents

Other manuals for Ford Escape 2013

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ford Escape 2013 and is the answer not in the manual?

Ford Escape 2013 Specifications

Curb Weight IconCurb Weight
curb weight 1.6L FWD3502 lbs
curb weight 1.6L 4WD3645 lbs
curb weight 2.0L FWD3592 lbs
curb weight 2.0L 4WD3732 lbs
curb weight 2.5L FWD3515 lbs
Seating and Interior IconSeating and Interior
seating capacity5
head room front39.9 inches
head room rear39.0 inches
shoulder room front56.0 inches
shoulder room rear55.3 inches
hip room front54.8 inches
hip room rear52.4 inches
leg room front43.1 inches
leg room rear36.8 inches
Passenger and Cargo Volume IconPassenger and Cargo Volume
passenger volume98.1 cu. ft.
cargo volume behind 1st row67.8 cu. ft.
cargo volume behind 2nd row34.3 cu. ft.
total interior volume132.4 cu. ft.
Fuel IconFuel
fuel tank capacity15.0 gallons
fuel requirement87 octane
fuel economy 2.5L FWD22/31 mpg (city/hwy)
fuel economy 1.6L FWD23/33 mpg (city/hwy)
fuel economy 1.6L 4WD22/30 mpg (city/hwy)
fuel economy 2.0L FWD22/30 mpg (city/hwy)
fuel economy 2.0L 4WD21/28 mpg (city/hwy)
Engine Specifications IconEngine Specifications
engine type 1.6LEcoBoost I-4
engine type 2.0LEcoBoost I-4
engine type 2.5Li-VCT I-4
displacement 1.6L97.6 cu. in.
displacement 2.0L122 cu. in.
displacement 2.5L152 cu. in.
horsepower 1.6L178 @ 5700 rpm
horsepower 2.0L240 @ 5500 rpm
horsepower 2.5L168 @ 6000 rpm
torque 1.6L184 lb.-ft. @ 2500 rpm
torque 2.0L270 lb.-ft. @ 3000 rpm
torque 2.5L170 lb.-ft. @ 4500 rpm
compression ratio 1.6L10.0:1
compression ratio 2.0L9.3:1
compression ratio 2.5L9.7:1
bore and stroke 1.6L3.11 x 3.20 inches
bore and stroke 2.0L3.44 x 3.27 inches
bore and stroke 2.5L3.50 x 3.94 inches
fuel system 1.6LDirect Injection
fuel system 2.0LDirect Injection
fuel system 2.5LSequential Multiport Injection
Weight and Dimensions IconWeight and Dimensions
wheelbase105.9 inches
length178.1 inches
height66.3 inches
width with mirrors81.8 inches
width without mirrors72.4 inches
track front61.5 inches
track rear61.6 inches
ground clearance7.9 inches

Related product manuals