EasyManuals Logo
Home>Ford>Automobile>Escape 2013

Ford Escape 2013 User Manual

Ford Escape 2013
892 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #29 background imageLoading...
Page #29 background image
How to Use the Automatic Locking
Mode
E142591
1. Buckle the combination lap and
shoulder belt.
2. Grasp the shoulder portion and pull
downward until the entire belt is pulled
out.
Allow the belt to retract. As the belt
retracts, you will hear a clicking sound. This
indicates the safety belt is now in the
automatic locking mode.
How to Disengage the Automatic
Locking Mode
Disconnect the combination lap and
shoulder belt and allow it to retract
completely to disengage the automatic
locking mode and activate the vehicle
sensitive (emergency) locking mode.
How to Extract Safety Belts in the
Rear Outboard Positions
Safety belts in the rear outboard positions
can lock if the seat back is returned firmly
to its upright position. The safety belts can
be unlocked using the following
procedures.
For vehicles where the rear seats recline:
1. Recline the seat to its full rear recline
position. See Safety Belts (page 26).
2. The safety belt should then unlock.
3. Return the seat back to its desired
upright position.
For vehicles with rear seats that do not
recline or are locked with the seat in its full
rear recline position:
1. Grasp the safety belt webbing at the
top of the seat back.
2. Pull the safety belt webbing forward,
firmly.
3. After pulling the safety belt forward,
allow the safety belt to feed back into
the safety belt retractor as much as
possible. If necessary, press the seat
back down to allow the safety belt
webbing to retract further.
4. The safety belt should then unlock.
5. If the safety belt does not unlock,
repeat steps 1-3.
Safety Belt Extension Assembly
WARNING
Position the safety belt height
adjusters so that the belt rests
across the middle of your shoulder.
Failure to adjust the safety belt properly
could reduce the effectiveness of the
safety belt and increase the risk of injury in
a collision.
If the safety belt is too short when fully
extended, a safety belt extension assembly
can be obtained from an authorized dealer.
Use only extensions manufactured by the
same supplier as the safety belt.
Manufacturer identification is located at
the end of the webbing on the label. Also,
use the safety belt extension only if the
safety belt is too short for you when fully
extended.
29
Safety Belts

Table of Contents

Other manuals for Ford Escape 2013

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ford Escape 2013 and is the answer not in the manual?

Ford Escape 2013 Specifications

Curb Weight IconCurb Weight
curb weight 1.6L FWD3502 lbs
curb weight 1.6L 4WD3645 lbs
curb weight 2.0L FWD3592 lbs
curb weight 2.0L 4WD3732 lbs
curb weight 2.5L FWD3515 lbs
Seating and Interior IconSeating and Interior
seating capacity5
head room front39.9 inches
head room rear39.0 inches
shoulder room front56.0 inches
shoulder room rear55.3 inches
hip room front54.8 inches
hip room rear52.4 inches
leg room front43.1 inches
leg room rear36.8 inches
Passenger and Cargo Volume IconPassenger and Cargo Volume
passenger volume98.1 cu. ft.
cargo volume behind 1st row67.8 cu. ft.
cargo volume behind 2nd row34.3 cu. ft.
total interior volume132.4 cu. ft.
Fuel IconFuel
fuel tank capacity15.0 gallons
fuel requirement87 octane
fuel economy 2.5L FWD22/31 mpg (city/hwy)
fuel economy 1.6L FWD23/33 mpg (city/hwy)
fuel economy 1.6L 4WD22/30 mpg (city/hwy)
fuel economy 2.0L FWD22/30 mpg (city/hwy)
fuel economy 2.0L 4WD21/28 mpg (city/hwy)
Engine Specifications IconEngine Specifications
engine type 1.6LEcoBoost I-4
engine type 2.0LEcoBoost I-4
engine type 2.5Li-VCT I-4
displacement 1.6L97.6 cu. in.
displacement 2.0L122 cu. in.
displacement 2.5L152 cu. in.
horsepower 1.6L178 @ 5700 rpm
horsepower 2.0L240 @ 5500 rpm
horsepower 2.5L168 @ 6000 rpm
torque 1.6L184 lb.-ft. @ 2500 rpm
torque 2.0L270 lb.-ft. @ 3000 rpm
torque 2.5L170 lb.-ft. @ 4500 rpm
compression ratio 1.6L10.0:1
compression ratio 2.0L9.3:1
compression ratio 2.5L9.7:1
bore and stroke 1.6L3.11 x 3.20 inches
bore and stroke 2.0L3.44 x 3.27 inches
bore and stroke 2.5L3.50 x 3.94 inches
fuel system 1.6LDirect Injection
fuel system 2.0LDirect Injection
fuel system 2.5LSequential Multiport Injection
Weight and Dimensions IconWeight and Dimensions
wheelbase105.9 inches
length178.1 inches
height66.3 inches
width with mirrors81.8 inches
width without mirrors72.4 inches
track front61.5 inches
track rear61.6 inches
ground clearance7.9 inches

Related product manuals