Honeywell Lynx Plus Series Installation And Setup Guide

Lynx Plus Series Installation and Setup Guide
- 47 -
✻81 Zone List Menu Mode
While in Program mode, press ✻81 to enter Zone List Menu Mode. This mode is used to program zone lists
for output devices (programmed in ✻80 Device Programming Menu Mode) or Chime-by-Zone in Zone List 3.
The following explains these prompts in detail. The left two columns identify the prompts and list the
available entries. The right-most column provides a further explanation of the entries.
Notes: (1) Any list may include any or all of the systems zone numbers
(2) A zone list can be assigned to more than one Powerline Carrier Device
(3) Entering a number other than one specified will give unpredictable results.
(4) Do not assign zones with zone types 20, 21 or 22 to a zone list.
(5) LynxSIA Plus ONLY
Zone List 2 should be used for Cross Zoning. When creating zone list 2 for cross zoning, include only 2
zones assigned to zone types 3, 4, or 5. If interior zones (zone type 4) are cross zoned, then both
zones in zone list 2 must be interior zones. Do not cross zone more than 2 zones, or zone types that
have delays (entry/exit zones, interior w/delay), or 24-hour zones, as these choices may produce
unpredictable operation and may not function as intended. If cross zoning is used, zone list 2 should
not be used for other purposes, such as triggering powerline carrier devices. If field ✻39 has been set
to “0” (no cross zoning), then Zone List 2 can be used for other purposes.
81
8181
81
ZONE
ZONE ZONE
ZONE LISTS
LISTS LISTS
LISTS MENU
MENUMENU
MENU
Zone List Programming
Entering “1” advances to the next prompt below. Entering “0” exits mode, upon which
this prompt blinks, indicating the mode is inactive.
SELECTIONS
0 = exit mode
1 = enter mode
A01
A01A01
A01
ZONE
ZONEZONE
ZONE LIST
LIST LIST
LIST NUMBER
NUMBERNUMBER
NUMBER
Zone List Number
Enter the Zone List Number 01, 02, or 03 to program (or 00 if no zone lists are used).
Note: Use Zone List 3 for Chime by Zone feature.
SELECTIONS
01-03 = zone list number to be programmed
00 = exit Zone List mode
[✻] = continue
b
ZN
ZN ZN
ZN ENTRY
ENTRYENTRY
ENTRY TO
TO TO
TO LIST
LIST LIST
LIST
Zone entry to list
Enter the 2-digit zone number for each zone number to add to the zone list by first
entering the zone number, then the [✻] key (for example, 01✻ 02✻ 03✻). The system will
announce the Voice Descriptor for the selected zone, if it is programmed. After all
desired zones are enrolled, enter “00” to advance.
SELECTIONS
01-41, 95, 96, 99 = zone numbers to add to zone list
[✻] = accept zone number and enter the next zone number
00 = accept zone number(s) and continue to next prompt
C
CC
C
DEL
DEL DEL
DEL WHOLE
WHOLEWHOLE
WHOLE ZN
ZN ZN
ZN LST
LSTLST
LST
Delete Entire Zone List
Enter “1” to delete the zone list. All zones in the zone list will be deleted automatically
and programming will return to the ZONE LIST NUMBER prompt. Enter “0” to save the
zone list or delete specific zones from the list.
SELECTIONS
0 = don’t delete; continue to next prompt
1 = delete the current zone list
d
DEL
DELDEL
DEL 1 ZN
1 ZN 1 ZN
1 ZN FRM
FRM FRM
FRM LST
LST LST
LST
Delete Zones from List?
Enter “0” to save the entire zone list. Programming will return to the ZONE LIST
NUMBER prompt. Enter “1” to delete a zone or zones in a zone list.
SELECTIONS
1 = continue to delete zones prompt
0 = don’t delete; continue to next zone list number prompt (A01)
[#] = return to zone list number prompt (A01)

Honeywell Lynx Plus Series Specifications

General

Brand	Honeywell
Model	Lynx Plus Series
Category	Security System
Language	English