JVC CA-TD5 User Manual

co"
6. Press the SET button.
Proceed to step 9
To use a Cassette Deck as the source
1. Press the left or right cursor key (<4 < or > p>)
until “TAPE” blinks on the display.
| |
i
_~~| =,
ta!
| ii 1
2. Press the SET button.
Proceed to step | mk. |
To Use the current source as the playback source:
1. Press the left or right cursor key {<< < or > >>}
until *- - ~~” blinks on the display. eae
2. Press the SET button. TER
P d to ste | DALY |
roceed to step | |
etting the volume level.
Press the left or right cursor key (Had < or > 1) to adjust Scat, ce _
¢ fl
the volume level. bik Le iT
VOLUME - A: Sets the volume level to 5. al
VOLUME - B: Sets the volume level to 12. | j
VOLUME - C: Sets the volume level to 20.
VOLUME - - : Sets the volume to the last volume setting used.
Press the ENTER button.
The “DAILY” indicator changes from a blinking display to a steady display. The ON TEME, OFF
TIME, PLAYBACK SOURCE (including the disc number and track number if a CD source is
selected) are displayed then the display reverts to the previous display, before the Timer was set.
Turn the power off if you made the timer settings with the power tumed on.
Mi If you make a mistake while setting the Timer, press the CANCEL button to retum to the previous
setting. You can use the CANCEL button to return to the On Time setting.
Hl A few seconds before the start time for the timer, the System automatically tums on the power and
displays “DAILY” and “TIMER” alternately on the display. When the set time is reached, playback
starts using the selected source. A few seconds before the end time for the timer. “TIMER” blinks on
the display and when the end time is reached the power is automatically turned off again.
MM If you change the source while the DAILY timer is running, the timer operation is cancelled.
Before Turning Off the Unit
MM If the source is a CD, make sure that there is a CD in the selected disc number.
MM If the source is a tape:
* Make sure that there is a tape in the Tape Tray.
* Check that the tape direction is correct. This is important especially when Reverse Mode is off.
* Set Reverse Mode on if you want to play both sides of the tape.
MM Select the Sound Mode if you' want to listen using a Sound Mode effect.
To change the DAILY Timer setting
To change the settings for the DAILY Timer, repeat the setting procedure from the beginning.
Turning the DAILY Timer On and Off
Once the DAILY Timer has been set, it. will be activated at the same time every day until the setting is
turned off.
To Turn the DAILY Timer Off
Press the MENU button.
“DAILY” appears on the display and the DAILY indicator in the “TIMER” section of the menu
display blinks.
Press the CANCEL button.
“DAILY OFF” appears on the display and the DAILY indicator in the TIMER section of the menus
goes out.
MENU
SET
ENTER
MENU
To Turn the DAILY Timer On Again
Press the MENU button.
“DALLY” appears on the display and the DAILY indicator in the “TIMER” section of the menu
display blinks.
Press the SET button...
Press the ENTER button.
The DAILY indicator in the TIMER section of the menu changes from a blinking display to a steady
display. The Tumer ON TIME, OFF TIME, PLAYBACK SOURCE (including the disc number and
track number if a CD source is selected), and VOLUME LEVEL are displayed on the display.
CAUTION: If the System is unplugged, or a power failure occurs, the
timer setting will be erased in a few days. if the settings are erased in
this way, reset the timer settings.
Setting the ONCE REC (Recording)
Timer
With the Recording Timer you can make a tape of a radio broadcast automatically whether or not you are
home. For the timer to work correctly, you need to make sure of the following in addition to setting the
time for the Tuner.and Cassette Deck to come on: .
ME You can set the ONCE REC Timer whether the Unit is on or off.
ME The tape you want to record onto must be in Tape Tray.
Press the MENU button. TEP T poo
“DAILY” appears on the display and the DAILY indicator in re
the “TIMER” section of the menu display blinks. Cee
Press the up or down cursor key ——
(>A
or
v
<<)
until
“REC”
blinks
TREE
PO
TE
on
the
display.
EAS.
Pave
1
“ONCE
REC”
appears
on the display
and the REC
indicator
in the “TIMER” section of the menu display blinks. | REC
Press the SET button.
The display changes to the On Time display.
Set the On Time and Off Time.
Use the ea < or > m1 key, and the SET key to set the start and end times in the same way as for the
DAILY Timer.
When you press the SET button after setting the Off Time, aoe
“TUNER” starts.to blink on the display. =
ies
_~
Te
ff et
f
‘Press the SET button.
The display changes to the preset channel selection screen.
« Press the left or right cursor key [_ hd Piit fm 10H
(<< or > P >) to select the preset me PRER Ufa '
channel you want to fisten to.
You can only select a station to receive from amongst | REC |
the preset channels.
Press the ENTER button.
The “REC” indicator changes from a blinking display to a steady display. The ON TIME, OFF TIME,
and preset channel number are displayed then the display reverts to the previous display, before the
Timer was set.
Turn the power off if you made the timer settings with the power turned on.
WE if you make a mistake while setting the Timer, press the CANCEL button to return to the previous
setting. You can use the CANCEL button to return to the On Time setting.
MM A few seconds before the start time for the timer, the System automatically tums on the power and
displays “ONCE REC” and “TIMER” altétnately on the display. When the set time is reached,
playback starts ‘using the selected source. A few seconds before the end time for the timer. “TIMER”
blinks on the display and when the end time is reached the power is automatically turned off again.
MM If you change the source while the ONCE REC timer is running the timer operation is cancelled.
39
YSSC1L-VO/SGL-VO

JVC CA-TD5 Specifications

General

Brand	JVC
Model	CA-TD5
Category	Speaker System
Language	English