JVC CA-TD5 User Manual

Before the Timer Starts
HB Check that tape direction is correct. This ts important especially when Reverse Mode is off.
MB Set Reverse Mode on if you want to record on both sides of the tape.
Setting the SLEEP Timer
MM The VOLUME control is automatically set to 0 when ONCE REC Timer is recording. Use the Sleep Timer to turn the Unit off after a certain number of minutes when it is playing. By setting
this timer, you can fal] asleep to music and know your Unit will turn off by itself rather than play all night.
It is very easy, and can be very disappointing, to forget to put ina ME You can only set the Sleep Timer when the Unit is on and a source is playing.
tape, or to accidentally leave a tape in Tape Tray you don’t want
recorded over. Although this happens to almost everyone at one time To set the SLEEP Timer, follow this procedure:
or another, we hope it won't happen to you! "$2 with the System on and a source playing,
SLEEP ;
ress the SLEEP button on the Remote
To Change the Recording Timer Setting (C5) Sitio -=) 7 er 7
To change the settings for the ONCE REC Timer, repeat the setting procedure from the beginning. The message “SLEEP” appears on the display. Se: tingle. whe
Turning the ONCE REC Timer On and Off Set the length of time you want the source to play before shutting
Once the ONCE REC Timer has been used to record a source. the setting is maintained but the Timer is off.
4 ae set to OFE * Each ume you press this button while the “SI-EEP™ indicator is blinking. it changes the number of
a To Turn the REC Timer Off Before the Timer Starts. minutes shown on the display in this sequence:
4 » Press the MENU button. + 10 — 20 — 30 > 60 ~ 90 © 120 — Cancelled ~ (back to the beginning)
“DAILY” appears on the display and the DAILY indicator in the “TIMER” section of the menu
4 display blinks. When the number of minutes you want show's on the display, just wait 5 seconds until the “SLEEP”
ae
ow
:
;
indicator
stops
blinking.
and
is
lighted
steadily.
~~
Press
the
up
or
down
cursor
key
(»»
A
or
v
<<}
until
“REC”
blinks
The
Unit
is
now
set
to
turn
off
after
the
number
of
minutes
you
set.
on
the
display.
“ONCE
REC”
appears
on
the
display
and
the
REC
indicator
in
the
“TIMER”
section
of
the
menu
To
Change
the
SLEEP
Timer
Setting
display blinks, Press the SLEEP button until the number of minutes you want appears on the display.
Press the CANCEL button. To Cancel the SLEEP Timer Setting |
Press the SLEEP button until the “SLEEP” indicator goes off on the display.
Tuming oft the Unit also cancels the SLEEP Timer.
cB
CANCEL
“REC OFF” appears on the display and the REC indicator in the TIMER section of the menus gaes
out.
e
4 To Record at the Same Time Again.
MENU
Timer Priority
Press the MENU button.
“DAILY™
appears
on
the
display
and
the
DAILY
indicator
in
the
"TIMER”
section
of
the
menu
Since
each
timer
can
be
set
independently,
you
may
wonder
what
happens
if
the
settings
overlap.
Here
are
display blinks. the priorities for each timer:
WE The ONCE REC Timer always has priority. This means that:
“ » Press the up or down cursor key (»» ~ or Vv <<) until “REC” blinks * If another timer is set to come on during a time when the ONCE REC Timer is operating, the
on
the
display.
other
timer
just
won't
come
on
at
all,
so
you
will
always
get
the
entire
program
on
tape.
“ONCE
REC”
appears
on
the
display
and
the
REC
indicator
in
the
“TIMER”
section
of
the
menu
*
Ifthe
ONCE
REC
Timer
is
set
to
come
on
while
another
timer
is
operating,
the
other
timer
will
display
blinks.
shut
off
10
seconds
before
the
ONCE
REC
Timer
is
set
to
turn
on,
and
the
ONCE
REC
Timer
will
then take over.
Mi The SLEEP Timer has the least priority. This means that if the SLEEP Timer is set while the DAILY
- Press the ENTER button. Timer is operating, the DAILY Timer settings are caneelled. However. if the DAILY Timer is set to
come while the SLEEP Timer is operating. the SLEEP Timer setting will be cancelled and the Unit
will use the settings trom the DAILY Timer.
, Press the SET button.
ed
Geese bas
~ The DAILY indicator in the TIMER section of the menu changes from a blinking display to a steady
display. The ON TIME, OFF TIME, and preset channel number are displayed then the display reverts
to the previous display, before the Timer was set.
Example
1
Setting
Operation
CAUTION: If the System is unplugged, or a power failure occurs, the
timer setting will be erased in a few days. If the settings are erased in ON one
PPLE
this way, reset the timer settings. ae mEL a) ,
SLEEP
Timer |
22:00 22:30 23:00 22:00 22:30
The ONCE REC Timer has prionty.
Example 2 7 :
Setting Operation
ON OFF ON OFF
ONCE REC ! [ a
Timer | ON | OFF } |
DAILY | ! | !
Timer
21:30 22:00 22:30 23:00 21:30 22:30
The ONCE REC Timer has priority.
40
441
Cc-1
YSSC1L-VO/SAL-VO

JVC CA-TD5 Specifications

General

Brand	JVC
Model	CA-TD5
Category	Speaker System
Language	English