JVC CA-TD5 User Manual

Z-|
Setting the Clock
The clock should be set before you start using this Unit.
If the clock has not been set, “0:00” appears in the display and the CLOCK indicator blinks.
You can set the clock regardless of whether the Unit is on or off.
English
q abi Press the MENU button. WoaTp ow
“DAILY ” blinks on the display and the TIMER selection indicator arta hoo
lights up. oe
| Dany ]
assoc)
Press the v << cursor key twice toselect ~—) ffi) iT i
“CLOCK”. fish fp da PH tts
“CLOCK ADJ” blinks on the display. (wer)
[ J
crock J
© Press the SET button.
The hour digits on the display blink.
Set the hour by pressing the << < or >>> cursor key.
Pressing the > cursor key increases the hour, and pressing irerrrt
the kad < cursor key decreases it. hfe Lode
Pressing down either of these cursor keys adjusts the setting continuously
until the key is released.
Press the SET button.
The minute digits on the display blink.
Set the minute by pressing the <4 < or >» cursor key.
Pressing the >I cursor key increases the minute, and pressing
the kd < cursor key decreases it. i ‘ i + : ad
Holding down either of these cursor keys allows you to continuously
adjust the minute setting in 10 minute increments until the key is released.
Press the ENTER button.
“CLOCK OK” appears on the display and the blinking “CLOCK™ fa PU be Probe
indicator disappears. The clock time starts from zero seconds from Ee Lit ty Re
the set time.
To correct a mistake:
eRe: HM Repeat the procedure from step | after pressing the ENTER key.
ME To correct a setting during the procedure, press the CANCEL key to go back to the previous setting
item,
Note: If you try to select DAILY or REC without first setting the clock, “CLOCK” and “ADJUST” are
displayed alternately on the display, and you will be unable to set the timers.
CAUTION: If there is a power failure, the clock loses its setting. The
display shows “0:00”, and the clock must be reset.
Adjusting the Brightness of the Display
In Standby mode you can adjust the brightness of the clock display.
Press the hi A, cursor key to make the display brighter.
Press the W ~#@ cursor key to make the display darker.
Common Operations
STANDBY indicator SEA S.A.BASS
PHONES soermeeeiO)-~ _ [2 anim VOLUME
* This iljustration is of CA-TDS5R,
CA-TD5 does not have the
DISPLAY MODE, EON ON/OFF,
TA/NEWS/INFO, and PTY
SEARCH buttons.
MENU CANCEL
Display
Source, Sound Mode ete. Volume Level
=! button
ae ia ARE, L
ids lal Eat GLEIvon
{TIMER} [CD P_ MODE] [REPEAT] [CO —* TAPE)
| DALY | [ CONTINUE [| OFF j wuroens
wes L— BALANCE —-R RES “J ke PROGRAM IE co a) (pe ag
- SEA CONTROL SSS SSS SSS SNe
SEA
MODE
Menu display
SURROUND MODE
» VOLUME When the System is being used, the display shows other ttems as well.
However, we have only shown the items described in this section.
This illustration shows all the items in the Menu display. However, the
menu items that are available will change, depending on the source
selected.
FADE MUTING
This illustration shows the Remote Control for CA-TDS55R.
The Remote Control for CA-TDS does not have the RDS
CONTROL button or include any RDS related labels.
Turning the Power On and Off
Turning the System On
Press the (/! button.
The display comes on and the STANDBY indicator goes out.
The System comes on ready to continue in the mode it was in when the power was last turned off.
oo sana
Turning the System Off
Press the (/| button again.
cyl The STANDBY indicator lights up and the display is blank, except for the clock display.
on) HB Some power (12 watts) is always consumed even though power is turned off (called Standby Mode).
HB To switch off the Unit completely, unplug the AC power cord from the AC outlet. When you unplug
the AC power cord, the clock will be reset to 0:00 immediately, and preset Tuner stations will be
erased after a few days.
YHSSQL-VO/SAL-VO

JVC CA-TD5 Specifications

General

Brand	JVC
Model	CA-TD5
Category	Speaker System
Language	English