Kyocera FS-9120DN Service Manual

1-1-3
FS-9120DN/9520DN
1-6 Assembly and Disassembly
1-6-1 Precautions for assembly and disassembly ......................................................................................... 1-6-1
(1) Precautions ..................................................................................................................................... 1-6-1
1-6-2 Paper feed section ............................................................................................................................... 1-6-2
(1) Detaching and refitting the forwarding, paper feed and separation pulleys.................................... 1-6-2
(2) Detaching and refitting the MP separation, MP paper feed and MP forwarding pulleys ................ 1-6-4
(3) Detaching and refitting the left and right registration cleaner ......................................................... 1-6-9
1-6-3 Laser scanner unit .............................................................................................................................. 1-6-11
(1) Detaching and refitting the laser scanner unit .............................................................................. 1-6-11
(2) Adjusting the skew of the laser scanner unit (reference).............................................................. 1-6-13
1-6-4 Drum section ...................................................................................................................................... 1-6-14
(1) Detaching and refitting the drum unit............................................................................................ 1-6-14
(2) Detaching and refitting the main charger unit ............................................................................... 1-6-14
(3) Detaching and refitting the drum separation claw assemblies ..................................................... 1-6-15
1-6-5 Developing section ............................................................................................................................. 1-6-16
(1) Detaching and refitting the developing unit .................................................................................. 1-6-16
1-6-6 Transfer section ................................................................................................................................. 1-6-17
(1) Detaching and refitting the transfer roller assembly ..................................................................... 1-6-17
1-6-7 Fuser section ...................................................................................................................................... 1-6-18
(1) Detaching and refitting the fuser unit ............................................................................................ 1-6-18
(2) Detaching and refitting the heat roller separation claws ............................................................... 1-6-18
(3) Detaching and refitting the press roller ......................................................................................... 1-6-19
(4) Detaching and refitting the fuser heater M and S ......................................................................... 1-6-20
(5) Detaching and refitting the heat roller ........................................................................................... 1-6-21
(6) Detaching and refitting the fuser unit thermistor 1 and 2 .............................................................. 1-6-22
1-6-10 PWBs ................................................................................................................................................. 1-6-23
(1) Detaching and refitting the main controller PWB .......................................................................... 1-6-23
(2) Detaching and refitting the engine controller PWB ....................................................................... 1-6-24
(3) Detaching and refitting the power supply unit............................................................................... 1-6-25
(4) Detaching and refitting the high-voltage transformer unit ............................................................. 1-6-26
(5) Detaching and refitting the operator panel PWB .......................................................................... 1-6-27
1-7 Requirements on PWB Replacement
1-7-1 Downloading printer firmware for upgrade ........................................................................................... 1-7-1
(1) Format for the firmware files ........................................................................................................... 1-7-1
(2) Downloading firmware via the parallel interface ............................................................................. 1-7-2
(3) Downloading firmware using the memory card .............................................................................. 1-7-3
(4) Downloading message data ........................................................................................................... 1-7-5
2-1 Mechanical construction
2-1-1 Paper feed section ............................................................................................................................... 2-1-1
2-1-2 Main charging section .......................................................................................................................... 2-1-5
2-1-3 Laser scanner unit ................................................................................................................................ 2-1-7
(1) Laser scanner unit .......................................................................................................................... 2-1-7
2-1-4 Developing section ............................................................................................................................. 2-1-10
(1) Formation of magnetic brush ........................................................................................................ 2-1-11
(2) Computing the absolute humidity ................................................................................................. 2-1-12
2-1-5 Transfer and separation sections ....................................................................................................... 2-1-13
2-1-6 Cleaning and charge erasing sections ............................................................................................... 2-1-15
2-1-7 Fuser section ...................................................................................................................................... 2-1-16
2-1-8 Eject and switchback sections ........................................................................................................... 2-1-18
2-1-9 Duplex unit ......................................................................................................................................... 2-1-20

Kyocera FS-9120DN Specifications

General

I/O ports	1 x Fast Ethernet 10/100 Base TX; 1 x High speed bi-directional parallel (IEEE 1284); 1 x USB 2.0 (High-Speed); 1 x KUIO LV Option-Interface slot.
Custom media sizes	88 x 148 mm - 297 x 450 mm
Power requirements	AC 220/240 V 50/60 Hz
Standard input trays	2 x 500
Recommended media weight	60 - 105 g/m²
Power consumption (active)	920 W
Maximum print size	297 x 420 mm
Maximum ISO A-series paper size	A3
Color	No
Print technology	Laser
Time to first page (black, normal)	7 s
Print speed (black, normal quality, A4/US Letter)	36 ppm
Memory slots	2
Storage media	HDD
Processor model	Power PC 750CX
Built-in processor	Yes
Maximum internal memory	544 MB
Internal storage capacity	20 GB
Sound power level (standby)	39 dB
Sound pressure level (printing)	53 dB
Total input capacity	1200 sheets
Maximum input capacity	4200 sheets
Paper tray 2 input capacity	200 sheets
Maximum duty cycle	55000 pages per month
Sustainability certificates	ENERGY STAR
Power consumption (standby)	160 W
Power consumption (PowerSave)	12 W

Weight and Dimensions

Dimensions (WxDxH)	585 x 639 x 615 mm