Omron CJ1M-CPU series User Manual

89
Specifications Section 2-1
2-1-2 General Specifications
Sched-
uled
inter-
rupts
Scheduled interrupts
in units of 0.1 ms
Starts scheduled interrupt tasks with a minimum inter-
val of 0.5 ms, at a precision of 0.1 ms. (Set in the PLC
Setup.)
Programming Manual:
6-5 Using a Scheduled Inter-
rupt as a High-speed Timer
Reset start by MSKS
instruction
When MSKS is executed, reset starts the internal timer
and standardizes the time to first interrupt.
Internal timer PV
reading by MSKS
instruction
When MSKS is executed, reads the time elapsed from
the start of the scheduled interrupt or the previous
scheduled interrupt.
Item Specifications
Power Supply Unit CJ1W-PA205R CJ1W-PA202 CJ1W-PD025
Supply voltage 100 to 240 V AC (wide-range), 50/60 Hz 24 V DC
Operating voltage and
frequency ranges
85 to 264 V AC, 47 to 63 Hz 19.2 to 28.8 V DC
Power consumption 100 VA max. 50 VA max. 50 W max.
Inrush current
(See note 3.)
At 100 to 120 V AC:
15 A/8 ms max. for cold start at room
temperature
At 200 to 240 V AC:
30 A/8 ms max. for cold start at room
temperature
At 100 to 120 V AC:
20 A/8 ms max. for cold start at room
temperature
At 200 to 240 V AC:
40 A/8 ms max. for cold start at room
temperature
At 24 V DC:
30 A/2 ms max. for cold start at
room temperature
Output capacity 5.0 A, 5 V DC (including supply to CPU
Unit)
2.8 A, 5 V DC (including supply to
CPU Unit)
5.0 A, 5 V DC (including supply
to CPU Unit)
0.8 A, 24 V DC
Total: 25 W max.
0.4 A, 24 V DC
Total: 14 W max.
0.8 A, 24 V DC
Total: 25 W max.
Output terminal (ser-
vice supply)
Not provided
RUN output
(See note 2.)
Contact configuration: SPST-NO
Switch capacity: 250 V AC, 2 A (resis-
tive load)
120 V AC, 0.5 A (inductive load), 24 V
DC, 2A (resistive load)
24 V DC, 2 A (inductive load)
Not provided.
Insulation resistance 20 M
Ω min. (at 500 V DC) between AC external and GR terminals
(See note 1.)
20 MΩ min. (at 500 V DC)
between DC external and GR
terminals (See note 1.)
Dielectric strength 2,300 V AC 50/60 Hz for 1 min between AC external and GR terminals (See note 1.)
Leakage current: 10 mA max.
1,000 V AC 50/60 Hz for 1 min between AC external and GR terminals (See note 1.)
Leakage current: 10 mA max.
Noise immunity 2 kV on power supply line (conforming to IEC61000-4-4)
Vibration resistance
10 to 57 Hz, 0.075-mm amplitude, 57 to 150 Hz, acceleration: 9.8 m/s
2
in X, Y, and Z directions for 80 minutes
(Time coefficient: 8 minutes
×coefficient factor 10 = total time 80 min.) (according to JIS C0040)
Shock resistance
147 m/s
2
3 times each in X, Y, and Z directions (Relay Output Unit: 100 m/s
2
) (according to JIS C0041)
Ambient operating
temperature
0 to 55
°C
Ambient operating
humidity
10% to 90% (with no condensation)
Atmosphere Must be free from corrosive gases.
Ambient storage tem-
perature
–20 to 70
°C (excluding battery)
Grounding Less than 100
Ω
Enclosure Mounted in a panel.
Weight All models are each 5 kg max.
CPU Rack dimen-
sions
90.7 to 466.7
× 90 × 65 mm (W x H x D) (not including cables)
Note: W = a + b +20 x n + 31 x m + 14.7
a: Power Supply Unit: PA205R = 80; PA202 = 45; PD025 = 60
b: CPU Unit: CJ1-H or CJ1 = 62; CJ1M-CPU1@ = 31; CJ1M-CPU2@ = 49
The total width is given by the following: W = 156.7 + n
× 20 + m × 31, where n is the number of 32-point I/O Units
or I/O Control Units and m is the number of other Units.
Safety measures Conforms to cULus and EC Directives.
Item Specifications Reference

Omron CJ1M-CPU series Specifications

General

Brand	Omron
Model	CJ1M-CPU series
Category	Controller
Language	English