Onkyo TX-NR708 User Manual

70
En
If you’ve connected your Zone 2 speakers to the AV
receiver, as explained in “Connecting Your Zone 2 Speak-
ers Directly to the AV receiver” (➔ 69), you must set the
“Powered Zone2” setting to “Act” (Activated).
Note
• Powered Zone 2 cannot be used if “Speakers Type(Front)” is
set to “Bi-Amp” (➔ 45).
• This procedure can also be performed on the AV receiver by
using SETUP, arrow buttons, and ENTER.
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust the
volume for Zone 2.
Controlling Zone 2 from the AV receiver
Note
• When Zone 2 is turned off, the output from the ZONE 2 12V
TRIGGER OUT goes low (0 volts).
Setting the Powered Zone 2
1
Press RECEIVER followed by SETUP.
The main menu appears onscreen.
Tip
• If the main menu doesn’t appear, make sure the appropri-
ate external input is selected on your TV.
2
Use q/w to select “Speaker Setup”, and then press
ENTER.
The “Speaker Setup” menu appears.
3
Use q/w to select “Speaker Settings”, and then
press ENTER.
The “Speaker Settings” menu appears.
4
Use q/w to select “Powered Zone2”, and use e/r
to select:
` Not Act
:
Use FRONT WIDE/ZONE 2 L/R terminals to
connect front wide speakers (Powered Zone 2
disabled).
` Act:
Use FRONT WIDE/ZONE 2 L/R terminals to
connect Zone 2 speakers (Powered Zone 2
enabled).
5
Press SETUP.
The setup menu closes.
2. Speaker Setup
1. Speaker Settings
2. Speaker Configuration
3. Speaker Distance
4. Level Calibration
5. Equalizer Settings
6. THX Audio Setup
2–1. Speaker Settings
Speaker Impedance
Speakers Type(Front)
Powered Zone2
6ohms
Normal
Not Act
Using Zone 2
1
To turn on Zone 2 and select an input source, press
ZONE 2 followed by an input selector button
within 8 seconds.
Zone 2 turns on, the ZONE 2 indicator lights.
Tip
• ZONE 2 12V TRIGGER OUT goes high (+12 V).
To select AM or FM, press TUNER input selector
and ZONE 2 repeatedly.
(North American models) You can also select SIR-
IUS.
To select the same source as that of the main room,
press ZONE 2 twice. “Zone 2 Selector: Source”
appears on the display.
2
To turn off Zone 2, press ZONE 2.
ZONE 2 indicator flashes.
Press OFF.
The zone is turned off, and the ZONE 2 indicator
goes off.
ZONE 2
OFF
ZONE 2 indicator
Input selector buttons

Onkyo TX-NR708 Specifications

Power

power supply	AC 220–240 V~, 50/60 Hz
power consumption	570 W
dynamic power (3 Ω)	250 W
dynamic power (4 Ω)	220 W
dynamic power (8 Ω)	130 W

Amplifier Specifications

power output (front L/R)	170 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
power output (center)	170 W (6 Ω, 1 kHz, 1 channel driven, IEC)
power output (surround L/R)	170 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
thd (total harmonic distortion)	0.08% (Rated power)
damping factor	60 (Front, 1 kHz, 8 Ω)

Audio Specifications

input sensitivity and impedance (line)	200 mV/47 kΩ
input sensitivity and impedance (phono MM)	2.5 mV/47 kΩ
frequency response	5 Hz–100 kHz/+1 dB, -3 dB (DSP bypass)
tone control (bass)	±10 dB, 50 Hz
tone control (treble)	±10 dB, 20 kHz

Video Specifications

video input sensitivity/output level and impedance (component and S-Video Y)	1.0 Vp–p/75 Ω
video input sensitivity/output level and impedance (component PB/CB, PR/CR)	0.7 Vp–p/75 Ω
video input sensitivity/output level and impedance (S-Video C)	0.25 Vp–p/75 Ω
video input sensitivity/output level and impedance (composite)	1.0 Vp–p/75 Ω
component video frequency response	5 Hz–100 MHz/0 dB, -3 dB

Tuner Specifications

tuning frequency range (fm)	87.5 MHz–108 MHz
tuning frequency range (am)	522 kHz–1, 611 kHz
fm/am preset memory	40 stations

Weight and Dimensions

weight	12.5 kg
dimensions	435 x 175 x 379 mm
carton dimensions	570 x 298 x 469 mm
carton weight	16.5 kg