Name: Onkyo TX-NR708
Brand: Onkyo
Rating: 5 (1 reviews)

To Next Page

To Previous Page

UP-A1 Dock

With the UP-A1 Dock, you can easily play the music,

photo, or movie stored on your Apple iPod through the AV

receiver and enjoy great sound.

You can use the AV receiver’s remote controller to operate

your iPod.

■ Basic Operation

Auto Power On

If you start iPod playback while the AV receiver is on

Standby, the AV receiver will automatically turn on and

select your iPod as the input source.

Direct Change

If you start iPod playback while listening to another input

source, the AV receiver will automatically select your iPod

as the input source.

Using the AV receiver’s Remote Controller

You can use the AV receiver’s remote controller to control

basic iPod functions (➔ 76).

■ Using Your iPod models Alarm Clock

You can use your iPod models Alarm Clock function to

automatically turn on your iPod and the AV receiver at a

specified time. The AV receiver’s input source will auto-

matically be set to the PORT selector.

Note

• To use this function, your iPod must be in the UP-A1 Dock, and

the UP-A1 Dock must be connected to the AV receiver.

• This function works only in the Standard mode (➔ 77).

• When you use this function, be sure to set the AV receiver’s vol-

ume control to a suitable level.

• When Zone 2 is turned on, you can’t use this function.

• You cannot use this function for sound effects on your iPod.

■ Charging Your iPod models Battery

The UP-A1 Dock charges your iPod models battery while

your iPod is in the UP-A1 Dock and connected to the

UNIVERSAL PORT jack on the AV receiver. While your

iPod is seated in the UP-A1 Dock, its battery will be

charged when the AV receiver is set to “On” or “Standby”.

Note

• When UP-A1 Dock that seated iPod is connected, the power

consumption on standby mode slightly increases.

■ Status Messages

• PORT Reading

The AV receiver is checking the connection with the

dock.

• PORT Not Support

The AV receiver do not support the connected dock.

•PORT UP-A1

UP-A1 Dock is connected.

Note

• The AV receiver displays the message “UP-A1” for several sec-

onds after recognizing the UP-A1.

• When the status message is not displayed on the AV receiver’s

display, check the connection to your iPod.

ND-S1

With the ND-S1 Digital Media Transport, you can easily

play the music stored on your iPod through the AV

receiver and enjoy great sound.

The ND-S1 processes the digital audio signal directly

from your iPod for high-quality digital audio output (opti-

cal or coaxial).

Note

• You must select “iPod” using ND-S1’s iPod/PC button.

• Set the AV receiver’s Input Display to “DOCK” (➔ 27).

Using the Onkyo Dock

Dock is sold separately.

For the latest information on the Onkyo Dock compo-

nents, see the Onkyo web site at:

http://www.onkyo.com

Before using the Onkyo Dock components, update

your iPod with the latest software, available from the

Apple web site.

For supported iPod models, see the instruction man-

ual of the Onkyo Dock.

The AV receiver may take several seconds to startup, so

you might not hear the first few seconds of the first

song.

■ Operating Notes

• Functionality depends on your iPod model and generation.

• Before selecting a different input source, stop iPod playback

to prevent the AV receiver from selecting the iPod input

source by mistake.

• If any accessories are connected to your iPod, the AV receiver

may not be able to select the input source properly.

• When connecting UP-A1 Dock to the radio tuner UP-HT1

(North American models)/UP-DT1 (European, Australian

and Asian models) with AUTO selected by the tuner’s Mode

Selector switch, you can switch the input source between UP-

A1 Dock and the tuner, by pressing PORT repeatedly on the

front panel.

• While your iPod is in the UP-A1 Dock, its volume control has

no effect. If you adjust your iPod models volume control while

it’s in the UP-A1 Dock, make sure it’s not set too high before

you reconnect your headphones.

• The Auto Power On function will not work if you set your

iPod in the UP-A1 Dock while it is playing.

• When Zone 2 is turned on, you can’t use Auto Power On and

Direct Change functions.

• Do not turn off the power with the iPod still connected to this

unit via the UP-A1 Dock.

• Set your iPod in the UP-A1 Dock after the AV receiver turns

on.

Other manuals for Onkyo TX-NR708

Brochure & Specs2 pages

Quick Setup2 pages

Specifications2 pages

Questions and Answers:

Need help?

Do you have a question about the Onkyo TX-NR708 and is the answer not in the manual?

Onkyo TX-NR708 Specifications

Power

power supply	AC 220–240 V~, 50/60 Hz
power consumption	570 W
dynamic power (3 Ω)	250 W
dynamic power (4 Ω)	220 W
dynamic power (8 Ω)	130 W

Amplifier Specifications

power output (front L/R)	170 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
power output (center)	170 W (6 Ω, 1 kHz, 1 channel driven, IEC)
power output (surround L/R)	170 W/Ch (6 Ω, 1 kHz, 1 channel driven, IEC)
thd (total harmonic distortion)	0.08% (Rated power)
damping factor	60 (Front, 1 kHz, 8 Ω)

Audio Specifications

input sensitivity and impedance (line)	200 mV/47 kΩ
input sensitivity and impedance (phono MM)	2.5 mV/47 kΩ
frequency response	5 Hz–100 kHz/+1 dB, -3 dB (DSP bypass)
tone control (bass)	±10 dB, 50 Hz
tone control (treble)	±10 dB, 20 kHz

Video Specifications

video input sensitivity/output level and impedance (component and S-Video Y)	1.0 Vp–p/75 Ω
video input sensitivity/output level and impedance (component PB/CB, PR/CR)	0.7 Vp–p/75 Ω
video input sensitivity/output level and impedance (S-Video C)	0.25 Vp–p/75 Ω
video input sensitivity/output level and impedance (composite)	1.0 Vp–p/75 Ω
component video frequency response	5 Hz–100 MHz/0 dB, -3 dB

Tuner Specifications