Pioneer sc-lx86 User Manual

80
09
Using other functions
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.
Set MULTI-ZONE to MULTI ZONE OFF.
! Disconnect the iPod and USB memory device from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI Setup on page 69).
1 Switch the receiver into standby.
2 While holding down ENTER on the front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET k/l, then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
! Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter ON
SPEAKERS FH/FW ON
Speaker System 9.1ch FH/FW
Speaker Setting
Front SMALL
Center SMALL
FH/FW SMALL
Surr SMALL
SB SMALLx2
SW YES
Surround Position IN REAR
Crossover 80 Hz
AMP ON
X-Curve OFF
DIMMER Brightest
Inputs
See Input function default and possible settings on page 47.
HDMI
HDMI Audio AMP
HDMI output HDMI OUT ALL
Control OFF
Control Mode --- (OFF)
ARC (Audio Return Channel) --- (OFF)
PQLS --- (AUTO)
Standby Through OFF
Setting Default
DSP
Power On Level LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
Auto Sound Retriever
iPod/USB, INTERNET RADIO, MEDIA
SERVER, FAVORITES, ADAPTER PORT
input function
ON
Other input functions OFF
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
Effect Level
ExtendedStereo 90
Other modes 50
2 PL II Music Options
Center Width 3
Dimension 0
Panorama OFF
Neo:X Options Center Gain
Neo:X CINEMA: 1.0
Neo:X MUSIC: 0.3
Neo:X MUSIC: 0.3
2 PL IIz Options
Height Gain MID
All Inputs
Listening Mode (2 ch/multi ch) AUTO SURROUND
Listening Mode (Headphones) STEREO
See also Setting the Audio options on page 73 for other default DSP settings.
MCACC
MCACC Position Memory M1: MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 3.00 m
Standing Wave (M1 to M6)
ATT of all channels/filters 0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1 to M6)
All channels/bands 0.0 dB
EQ Wide Trim 0.0 dB

Pioneer sc-lx86 Specifications

General

Receiver type	Surround
Output impedance	6 Ω
Speaker selector	A+B
Audio output channels	9.1 channels
Total Harmonic Distortion (THD)	1 %
Power output per channel (1KHz@6 Ohm)	190 W
Power output per channel (20-20KHz@8 Ohm)	- W
HDMI in	8
AC (power) in	Yes
Remote (IR) input	1
Composite video in	4
Digital audio optical in	2
Multichannel audio input type	RCA
Component video (YPbPr/YCbCr) in	3
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Supported radio bands	AM, FM
Optical drive included	No
Display	-
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital Plus, Dolby Pro Logic, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS 96/24, DTS-ES, DTS-HD, DTS-HD Master Audio
Apple docking compatibility	iPad, iPhone, iPod
On Screen Display (OSD) languages	DEU, DUT, ENG, ESP, FRE, ITA, RUS
Graphical user interface (GUI) language	English, French, German, Italian, Russian, Spanish
AC input voltage	230-240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	370 W
THX-certified	THX Select2 Plus
Cables included	AC