Roland AX-EDGE Parameter Guide

Program Parameters
13
CTRL PEDAL (Control Pedal)
Parameter
[K] [J] buttons
Value
[-] [+] buttons
Explanation
Source PRG, SYS
Specifies whether the parameter
controlled by a pedal connected to the
PEDAL jack follows the program’s settings
(PRG) or the system settings (SYS).
Func
(Function)
Specify the function that is assigned to the pedal when CTRL
PEDAL: Source is set to “PRG.”
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
* CC74 (Cutoff) varies in the range of -64–0,
and CC71 (Resonance), CC72 (Release), CC73
(Attack), and CC75 (Decay) vary in the range
of 0–+63.
AFT Aftertouch
BEND DOWN Lowers the pitch.
BEND UP Raises the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
PART FADE2
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
Pole (Pedal Polarity)
STANDARD,
REVERSE
Specifies the polarity of the pedal
connected to the PEDAL jack.
CTRL RIBBON (Control Ribbon Controller)
Parameter
[K] [J] buttons
Value
[-] [+] buttons
Explanation
Source PRG, SYS
Specifies whether the parameter
controlled by the ribbon controller
follows the program’s settings (PRG) or
the system settings (SYS).
Posi
(Position Function)
Specifies the function that is assigned to the ribbon controller
(left/right axis) when CTRL RIBBON: Source is set to “PRG.”
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
NOTE
If a CC with a value range of 0–127 is assigned to
Position Function, the value will be the center point
(64) when you're not touching the ribbon.
AFT Aftertouch
PITCH BEND Raise or lower the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
PART FADE2
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127
Pres (Pressure Function)
Specifies the function that occurs when the ribbon controller is
pressed (pressure axis).
OFF No function is assigned.
CC01–31, 32 (OFF),
33–95
Controller number 1–31, 32, 33–95
* CC74 (Cutoff) varies in the range of -64–0,
and CC71 (Resonance), CC72 (Release), CC73
(Attack), and CC75 (Decay) vary in the range
of 0–+63.
AFT Aftertouch
BEND DOWN Lowers the pitch.
BEND UP Raises the pitch.
PART FADE1
Continuously control the level of parts
1–4.
Part1
Part2
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part3
Part4
expression 127
expression 0
Value0
127
Part1
Part4
expression 127
expression 0
Value0
127

Roland AX-EDGE Specifications

General

Brand	Roland
Model	AX-EDGE
Category	Synthesizer
Language	English